background image

instructions for

power scan automotive probe/scope 

0-30v

model no:

 pp100.v2

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. saFetY

 

‰

iF You are in anY Doubt about eLectricaL saFetY consuLt a QuaLiFieD eLectrician.

 

9

   only for use with 2V - 24V dc systems.

 

8

Do not

 apply voltage or current to the probe that exceeds the specified maximum of 30V dc.

 

8

Do not

 use on any circuit directly or indirectly connected to Ac lines or any other Ac power source. 

 

8

Do not

 use with any component or circuits on the vehicle’s ignition system.

 

9

Before using this device, check the vehicle’s electrical wiring and disconnect any part or system sensitive to voltage and current pulses 

such as air bags, electronic control modules, etc.

 

9

Always check the instructions and procedures indicated in the vehicle service manual before attempting to disconnect any part or 

sub-system of the electrical circuit.

 

9

When not in use, store carefully in a safe, dry, childproof location. Avoid extremes of temperature.

 

8

Do not

 use the tool around explosive gases, vapour or dust. When the power switch is operated (forwards or backwards), voltage is 

present at the tip of the probe which may cause sparks when contacting ground or certain other circuits.

 

8

Do not 

use leads if damaged or if the wire is bared in any way.

 

8

Do not

 use the equipment when you are tired or under the influence of alcohol, drugs or intoxicating medicines.

 

8

Do not

 use this tool for any purpose other than that for which it has been designed. 

2. introDuction

Probably the most advanced automotive probe on the market, with a huge range of functions for effective automotive diagnostics, making short 

circuits and bad earths easy to find. Features a scope function to visually test component signals, with the added benefit of maximum/minimum 

volts, frequency and duty cycle displayed. Allows components to be activated in situ or prior to installation. The fly lead allows continuity and polarity 

testing with a high-contrast colour LCD display giving a 7mm high read-out. Features audible and positive/negative voltage indicator and two 

integral work lights. 6mtr lead connects to the battery supply and reaches all areas of the vehicle. includes a vehicle accessory socket adaptor and 

6mtr extension cable. supplied in carry-case.

3. speciFication

model no: ............................................................... PP100.V2

dc voltage: .................................................................. 0-30V

frequency: ............................................................... 0-10KHz

duty cycle: ...................................................................1-99%

resistance: ..........................................................

50Ω-199kΩ

continuity test audible: ..................................................

<50Ω

scope function: ................................................................ yes

Back light: ........................................................................ yes

circuit breaker reset: ........................................................ yes

Key to fig.1

Probe tip – contacts the circuit or component to be tested.

2 Work lights – illuminate work area. 

3 Red/Green Polarity Indicator – Identifies positive, negative or open circuits. 

   the red indicator lights when the probe tip is contacting a positive circuit. 

   the green indicator lights when the probe tip is contacting a negative circuit.

4 lcd display 

5 circuit Breaker reset – resets the tool when the circuit breaker is tripped

6 Power switch – When operated conducts a positive or negative battery current 

   to the tip for activating and testing the function of electrical components.

7 mode Button – selects the work mode: dc voltage, scope, resistance & 

   audible indicator.

8 speaker – When the audible indicator is turned on, emits a tone.

9 Auxiliary Ground Lead

10 Adaptor – connects to the battery supply via clips or cigarette lighter adaptor.

P

P100.V2| Issue 1 13/06/17

Original Language Version

© Jack sealey limited

refer to

instruction 

manual

Wear eye

protection

fig.1

Содержание PP100.V2






Отзывы: