background image

4.

OPERATION

4.1.

Regulator

- The output pressure is controlled by the knob. Before pressurising the air system 

for the first time, pull out and rotate the knob anticlockwise to remove any loading on the 
regulator spring. Pressurise the system and then rotate knob clockwise to set required output 
pressure, as shown on gauge. When the required pressure is achieved push in knob to prevent 
inadvertent adjustment.

Note: 

For correct pressure setting always adjust up from a lower pressure. Therefore to 

reset from 90 to 70psi for example, reduce pressure from 90 to 60psi and then increase to 70psi.

4.2.

Filter

- The bowl should be drained regularly to prevent an excessive build-up of water/oil. Pull down 

the drain valve at the bottom of the bowl, allow to drain and then release. Drain valve has 
female 1/8” BSP outlet.

4.3.

Lubricator

- Remove the filler plug 

(fig.2.A)

and fill bowl up to max. level, with air tool oil. 

This can be done with the air line pressurised. With air flowing through the lubricator the oil 
delivery rate can be adjusted by screw 

(fig.2.C)

whilst watching the drip rate through the sight 

dome 

(fig.2.B)

. The oil delivery rate will automatically increase or decrease in line with the air flow.

4.4.

Both the filter and the lubricator are supplied with a metal bowl guard. To remove the guard, pull 
down the latch 

(fig.3.D)

and rotate the guard until either of the two pairs of lines 

(fig.3.E)

on 

the guard align with the similar marks 

(fig.3.F)

on the head. The guard can now be removed.

To refit, slide the top of the guard into the head with the guard and head markings aligned, 
and then rotate the guard so that the latch aligns with the marks on the head. The latch will 
lock into place.

5.

PARTS

6.

DECLARATION OF CONFORMITY

The following fittings are also available from your supplier:

SA1/1214F

 . .1/2”BSP male -1/4”BSP female reducer

SA1/3814F

 . .3/8”BSP male -1/4”BSP female reducer

SA1/1414

 . . .1/4”BSP male -1/4”BSP male connector

Declaration of Conformity 

We, the sole importer into the UK, declare that the products listed here are in conformity with the following standards and directives.

The construction files for these products are held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.

For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.

Air Regulator, Filter & Lubricator Range

Models: SA106, SA106FR, SA106F,

SA106L & SA106R

97/23/EC Pressure Equipment Directive

98/37/EC Machinery Directive

93/68/EEC Marking Directive

Signed by Mark Sweetman

Date: 12th April 2006

3.

CONTENT & INSTALLATION

3.1.

Confirm that all items are present and undamaged. If any parts are missing or damaged please contact the supplier.

SA106

- Combined filter, regulator with gauge, lubricator and mounting bracket.

SA106FR

- Combined filter, regulator with gauge and mounting bracket.

SA106F

- Filter.

SA106L

- Lubricator.

SA106R 

- Regulator with gauge and mounting bracket.

3.2.

Fig.1 shows a typical air line installation. The filter is located 
upstream of the regulator - unless combined, as in SA106
and SA106FR - and the lubricator downstream.

3.3.

Filter/regulator - Install using the mounting bracket provided. 
Before connecting system piping ensure that gauge is visible, 
unused gauge port is sealed with plug provided and that flow 
direction arrow matches system air flow.

3.4.

Filter and Lubricator - Install into air piping or connect directly to bracket mounted regulator using fittings provided. Always check that
flow arrows are correct and that filter is upstream, and lubricator downstream, of regulator.

Note:

To ensure air-tight joints, use PTFE tape.

fig.1

fig.2

fig.3

SA106/106FR/106F/106L/106R - 1 - 120406

01284 757500

01284 703534

[email protected]

Sole UK Distributor
Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

email

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION: 

For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

MODEL:

SA106

SA106FR

SA106F

SA106L

SA106R

Filter Bowl:

SA106.B

SA106.B

SA106.B ---

---

Lubricator Bowl:

SA106.B1 ---

---

SA106.B1 ---

Regulator gauge: SA106.G

SA106.G

---

---

SA106.G

Plastic Ring:

SA106.PR SA106.PR

---

---

SA106.PR

Wall Bracket:

SA106.WB SA106.WB1 ---

---

SA106.WB1

Отзывы: