These bench mounted variable speed drills are suitable for industrial, agricultural and woodworking applications. The drills are fitted
with flip-up safety guards and “No-Volt Release” switches which prevent accidental restart after a mains power interruption. A rack and
pinion feed shaft with preset depth control for repetitive work is also included. Morse taper spindles accept taper shank bits.
Mortice attachments, work clamps and vices are also available for these drills, contact your local Sealey dealer for information.
Model PDM155B has a built-in lamp to illuminate the drill bit and workpiece.
4.1. Package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your dealer immediately.
3
Head
Assembly
3
Base
3
Chuck and Key
3
Column with Flange
3
Feed Handle
3
Table Arm, Bracket and Worm
3
Adjusting Handle with Set Screw (table)
3
Table
3
Rack and Rack Ring
3
Pivoted Clamp Bolts (2 - table arm & bracket)
3
Bolts (4)
3
Safety Guard
3
Arbor
3
Set Screws (2)
3
Wedge
3
Hex. Keys (2)
3
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
3
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non-stable work piece with a clamp, vice or other adequate holding device.
3
Avoid unintentional starting.
7
DO NOT
use the drill for a task it is not designed to perform.
7
DO NOT
allow untrained persons to operate the drill.
7
DO NOT
get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT
operate the drill if damaged.
7
DO NOT
use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
the drill when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
7
DO NOT
exceed the rated capacity of the drill.
7
DO NOT
operate the drill if any parts are missing as this may cause failure and/or personal injury.
7
DO NOT
leave the drill operating unattended.
7
DO NOT
operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT
pull the cable from the power supply.
3
When not in use switch off the drill, remove plug from the power supply and do not leave until the drill chuck has come to a complete stop.
3. TECHNICAL SPECIFICATIONS
2. DESCRIPTION
4. CONTENT
Model
PDM125B
PDM155B
PDM100B
Chuck size (mm)
16
16
16
Spindle Nose Taper
MT2
MT2
MT2
Swing (mm)
403
460
314
Chuck to Upright Face (mm)
165
190
127
Spindle Travel (mm)
80
80
60
Number of Speeds
16
16
12
Speed Range (rpm)
190 - 3000
190 - 3000
180 - 2740
Spindle to Table - max. (mm)
485
475
420
Spindle to Base - max. (mm)
700
660
540
Working Table (mm)
254 x 254
290 x 290
200 x 200
Working Base (mm)
205 x 200
205 x 200
165 x 155
Overall Base (mm)
450 x 270
495 x 290
345 x 210
Column Diameter (mm)
73
80
60
Voltage (AC)
Overall Height (mm)
230
230
1050
1050
230
850
Motor (W) Nominal/Maximum
370/550
370/550
370/550
Original Language Version
PDM100B, PDM125B, PDM155B Issue: 4 (SP) - 10/12/13
Weight
35Kg
52Kg
62Kg
Optional Keyless Chuck
PDM/KC
PDM/KC
PDM/KC
© Jack Sealey Limited
Integral Work Light
NO
NO
YES
Collar Diameter (mm)
55
55
60
