Original Language Version
© Jack Sealey Limited
9
When charging the internal battery, work in a well ventilated area and do not restrict the ventilation in any way.
9
Be sure the area around the battery is well ventilated while the Roadstart is being used.
9
Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead-acid battery. A lead-acid
battery can produce a short-circuit current high enough to weld a ring or the like to metal, causing a severe burn.
9
Be extra cautious, to reduce the risk of dropping a metal tool onto the battery. It might spark or short-circuit the battery or other
electrical part that may cause an explosion.
9
To prevent sparking, NEVER allow clamps to touch together or contact the same piece of metal.
9
Consider having someone close enough by to come to your aid when you work near a lead-acid battery.
9
Have plenty of fresh water and soap nearby in case battery acid contacts your skin, clothing or eyes.
9
Wear complete eye and body protection, including safety goggles and protective clothing. Avoid touching your eyes while working near
the battery.
9
If battery acid contacts your skin or clothing, immediately wash the area with soap and water. If acid enters your eye, immediately flood
the eye with cold running water for at least 10 minutes and get medical attention right away.
9
If battery acid is accidentally swallowed, drink milk, the whites of eggs or water.
DO NOT
induce vomiting. Seek medical attention
immediately.
2. INTRODUCTION
High performance (2x 23Ah PBIW4600, 2 x 32Ah PBIW6200) AGm battery, specially formulated to jump-start up to 1500hp diesel vehicles.
Rotomolded high durability casing with lifetime warranty. Patented 4A microprocessor controlled speed charging and thermal runaway
protection. Unlike other Roadstart packs, can be left safely on charge continuously. Audible warning signals if the unit has been turned on for too
long without being connected to a battery and reverse polarity. Isolating rotary on/off switch and analogue display showing the internal battery
level. 12V Output socket can be used as a memory saver as well as for powering accessories such as mini compressors. Ventilation system
vents gases directly out of the casing via a ‘Whistle’ outlet, warning the user of a potential issue. A fuse integrated in the (+) clamp provides
short-circuit and overload protection. Heavy-duty clamps with a braided link between each jaw for maximum power transmission. Curved clamps
provide easier access to awkward battery terminals.
3. SPECIFICATION
4. FEATURES
4.1.
DESCRIPTION
1. Reverse polarity buzzer
2. 12V outlet, protected by 16A external circuit breaker
3. 500A fuse
4. Voltmeter
5. Push button for voltmeter
6. Voltage selector
7. Charger input plug
4.2.
VOLTMETER
4.2.1.
Press the button to show the charge level of the Roadstart.
4.2.2.
Half an hour after disconnecting the charger from the Roadstart, the voltmeter must indicate about 13 volt for a full charge.
4.3.
ALTERNATOR TESTING
4.3.1.
After starting rev the engine to 2000 rpm, leave the Roadstart connected to the vehicle and press the voltmeter push button. The
voltmeter must indicate between 14 and 14.4 volt if the alternator is functioning correctly.
4.3.2.
Model no
PBIW4600
PBIW6200
Auxiliary output
1 x 12V
1 x 12V
Cable and clamp length
1.4m
1.4m
Peak amps
4600A (12V), 2300A (24V)
6200A (12V), 3100A (24V)
Starting current
1800A/900A
2400/1200A
Voltage
12/24V
12/24V
PBIW4600, PBIW6200 | Issue:2 (6) 04/11/19
