InstructIons for:
ENERGY SAVING WORK LAMPS 36W
Model no's:
ML36, ML36T, ML36TD
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND/OR WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.1 .
ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also
recommend that a residual current device (rcd) is used. It is particularly important to use an rcd with portable products that are
plugged into a supply which is not protected by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual
current device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6. Important: ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. do not pull or carry the appliance by the power cable.
1.1.8. do not pull the plug from the socket by the cable.
1.1.9. do not use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
to rewire, connect the wires as indicated above do not connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm
²
, but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm
²
section cable.
1. SAFETY INSTRUCTIONS
FUSE RATING
5 AMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
1.2.
GENERAL SAFETY
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
lamp.
do not immerse lamp in water.
ensure the lamp is disconnected from the mains before attempting to change the fluorescent tube.
Maintain the
lamp in good condition (use an authorised service agent).
ensure there are no flammable liquids or vapours present.
DO NOT
use lamp for any purpose other than that for which it is designed.
DO NOT
pull the cord to remove the plug from the power supply.
When not in use unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODUCTION
fitted with a compact fluorescent energy saving bulb, which emits a bright white light. low wattage means a low energy consumption which helps
to reduce energy bills. lighting brackets feature angle adjustment.
ML36 -
Mounted on a floor standing bracket, which features angle adjustment. Incorporates pre-drilled holes for optional wall mounting.
ML36T -
Mounted on a two-position telescopic tripod with folding legs and cable storage hooks.
ML36TD -
removable head allows use as free-standing or can be mounted on a telescopic tripod stand.
stand features two-position telescopic uprights with folding legs and cable storage hooks. suitable for lighting workshops, garages and any other
environment where light is limited. supplied with 3mtr lead and Bs approved plug.
MODEL No's . . . . . . . .ML36 . . . . . . . . . . . . . . ML36T . . . . . . . . . . . . . ML36TD
Power . . . . . . . . . . . . . .36W . . . . . . . . . . . . . . . 36W . . . . . . . . . . . . . . . 2x36W
supply. . . . . . . . . . . . . .230V. . . . . . . . . . . . . . . 230V. . . . . . . . . . . . . . . 230V
Min/Max Height . . . . . .n/a . . . . . . . . . . . . . . . . 900 / 1500mm . . . . . . . 900 / 1500mm
Bulb fitting . . . . . . . . . .e27 screw cap . . . . . . e27 screw cap . . . . . . e27 screw cap
replacment Bulb . . . . .Ml36B . . . . . . . . . . . . . Ml36B . . . . . . . . . . . . . Ml36B
Original Language Version
Ml36, Ml36t, Ml36t Issue: 1 - 20/05/10
