p
WARNING!
Ensure that you read, understand and apply the Safety Instructions before using the compressor.
p
WARNING!
Connect
only
to 12V DC supply capable of providing a current of at least 8 amps.
3.1.
Tyre inflation
3.1.1. Remove the dust cap from the tyre valve and push the connector (A - locking lever in line with connector
body as shown) onto the valve as far as it will go. Lock in place by pressing down the locking lever.
If air loss can be heard remove the connector and then refit.
3.1.2. With the compressor switch (C) off, plug the cigarette lighter adaptor (B) into the vehicles lighter socket.
Note that it may be necessary to turn on the ignition to get power to the lighter socket.
3.1.3. Switch on the compressor.
3.1.4. When the gauge (E) shows the required pressure (see vehicle handbook) switch off the compressor and
unlock and remove the connector (A) from the tyre valve. Refit the tyre valve dust cap.
3.1.5. At the first opportunity have the tyre pressure checked with a gauge of known accuracy.
3.2.
Inflatables
3.2.1. Select the appropriate adaptor from the three provided (D) and secure it in the connector (A).
3 .2.2. Insert the adaptor (D) into the inflatable and proceed as in 2.1. to connect and start the compressor.
Take care not to over-inflate.
p
WARNING!
Ensure that you read, understand and apply the Safety Instructions before using the compressor.
p
WARNING!
Connect
only
to 12V DC supply capable of providing a current of at least 8 amps.
3.1.
Tyre inflation
3.1.1. Remove the dust cap from the tyre valve and push the connector (A - locking lever in line with connector
body as shown) onto the valve as far as it will go. Lock in place by pressing down the locking lever.
If air loss can be heard remove the connector and then refit.
3.1.2. With the compressor switch (C) off, plug the cigarette lighter adaptor (B) into the vehicles lighter socket.
Note that it may be necessary to turn on the ignition to get power to the lighter socket.
3.1.3. Switch on the compressor.
3.1.4. When the gauge (E) shows the required pressure (see vehicle handbook) switch off the compressor and
unlock and remove the connector (A) from the tyre valve. Refit the tyre valve dust cap.
3.1.5. At the first opportunity have the tyre pressure checked with a gauge of known accuracy.
3.2.
Inflatables
3.2.1. Select the appropriate adaptor from the three provided (D) and secure it in the connector (A).
3.2.2. Insert the adaptor (D) into the inflatable and proceed as in 2.1. to connect and start the compressor.
Take care not to over-inflate.
INSTRUCTIONS FOR
12V MINI AIR COMPRESSOR
MODEL:
MAC1250
Thank you for purchasing a Sealey compressor. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
MAC1250 - 2 - 241003
1.
SAFETY INSTRUCTIONS
3
Familiarise yourself with the application, limitations and potential hazards of the compressor.
p
WARNING!
Disconnect the compressor from the cigarette lighter socket before changing accessories,
servicing or performing any maintenance.
3
Use only the supplied adaptors.
3
Maintain the compressor in good condition,
DO NOT
use if damaged.
3
Ensure that there are no flammable or combustible materials (including gases) near the compressor when in use.
p
WARNING!
This compressor is capable of high pressure.
DO NOT
exceed the maximum safe pressure of
the item being inflated.
p
WARNING!
The gauge on the compressor is for guidance only. Where pressure is critical (e.g. tyres) check
with a gauge of known accuracy.
7
DO NOT
leave the compressor operating unattended.
7
DO NOT
operate in wet or damp conditions.
p
WARNING!
To prevent overheating and subsequent damage to the unit, switch off after 10 minutes continuous
operation and allow to cool for 30 minutes before switching back on.
3
After use store in a safe, dry, childproof area with the connector locking lever in the unlocked position.
3.
OPERATION
INSTRUCTIONS FOR
12V MINI AIR COMPRESSOR
MODEL:
MAC1250
Thank you for purchasing a Sealey compressor. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
MAC1250 - 2 - 241003
1.
SAFETY INSTRUCTIONS
3
Familiarise yourself with the application, limitations and potential hazards of the compressor.
p
WARNING!
Disconnect the compressor from the cigarette lighter socket before changing accessories,
servicing or performing any maintenance.
3
Use only the supplied adaptors.
3
Maintain the compressor in good condition,
DO NOT
use if damaged.
3
Ensure that there are no flammable or combustible materials (including gases) near the compressor when in use.
p
WARNING!
This compressor is capable of high pressure.
DO NOT
exceed the maximum safe pressure of
the item being inflated.
p
WARNING!
The gauge on the compressor is for guidance only. Where pressure is critical (e.g. tyres) check
with a gauge of known accuracy.
7
DO NOT
leave the compressor operating unattended.
7
DO NOT
operate in wet or damp conditions.
p
WARNING!
To prevent overheating and subsequent damage to the unit, switch off after 10 minutes continuous
operation and allow to cool for 30 minutes before switching back on.
3
After use store in a safe, dry, childproof area with the connector locking lever in the unlocked position.
3.
OPERATION
Sturdy composite casing incorporating cable tidy and plug storage. Powered by a 12V motor and is suitable for
inflating tyres on cars, vans and 4x4s. Fitted with an integral gauge that reads up to17bar/250psi. Supplied
with 3mtr power cable with in line rotary power switch and plug for use in a cigarette lighter socket, 450mm high
pressure hose with clip on connector and accessory kit including ball needle and adaptors for inflatables.
2.
INTRODUCTION
2.
INTRODUCTION
Sturdy composite casing incorporating cable tidy and plug storage. Powered by a 12V motor and is suitable for
inflating tyres on cars, vans and 4x4s. Fitted with an integral gauge that reads up to17bar/250psi. Supplied
with 3mtr power cable with in line rotary power switch and plug for use in a cigarette lighter socket, 450mm high
pressure hose with clip on connector and accessory kit including ball needle and adaptors for inflatables.
