4.1. TELESCOPIC STANDS (LED130T.V2, LED130TD.V2, LED130110T.V2, LED130110TD.V2)
4.1.1. Loosen the locking thumb screw (fig.5D) on the tripod leg collar and slide the collar down, spreading
the legs. Tighten the screw to secure legs in the required position.
4.1.2. Fix the removable head stand (fig.4) or the singular lamp onto the top of the stand, secure with hand
screw (fig.5A). Check that the electrical cable runs directly down the stand to the floor.
DO NOT
allow
the cable to extend across the workshop above floor level. Models have storage hooks for excess
cable (fig.5E).
4.1.3. To extend the upright, loosen the locking collar at the end of each section (fig.5B), raise the inner
support to the required height and tighten the locking collars.
4.1.4. Check that the assembly is secure and that all nuts and bolts are tight (
DO NOT
overtighten). Stand
light on a suitable, level surface before use.
4.1.5. LED130TD.V2 and LED130110TD.V2 can be removed from the tripod and used with their integral stand
(fig.4).
4.2. GENERAL
4.2.1. Use only Sealey replacement parts. Electrical repairs must only be undertaken by a qualified electrician.
4.2.2. Clean the light with a dry, dust-free cloth.
DO NOT
use solvents or abrasives to clean the light.
4.2.3. Avoid touching the glass shield as handling may reduce service life and cause the glass to crack. If
necessary clean the shield (when cold) with alcohol and a soft cloth.
4.2.4. If the glass is damaged, replace it immediately. Use genuine Sealey replacement glass.
DO NOT
use
other glass and
DO NOT
use the light without the glass shield.
4.2.5 Should the unit become wet, unplug from mains and wipe dry before storing.
DO NOT
use the light without the weather seal intact.
Original Language Version
LED130T.V2, LED130TD.V2, LED130110T.V2, LED130110TD.V2 Issue: 1 - 30/07/14
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or phone 01284 757500.
DO NOT
stand on the legs of a telescopic stand, and
DO NOT
hang other items, or tools, from a telescopic stand.
DO NOT
use the light without the front glass shield. Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack.
DO NOT
use the light without the weather seals intact.
DO NOT
use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a safe, dry, childproof
location.
© Jack Sealey Limited
fig.4
fig.5
MODEL No: . . . . LED130T.V2 . . . .LED130TD.V2 . . LED130110T.V2 LED130110TD.V2
Power: . . . . . . . . 9W. . . . . . . . . . . .18W . . . . . . . . . . 9W . . . . . . . . . . . 2x8W
Supply: . . . . . . . . 230V . . . . . . . . . .230V. . . . . . . . . . 110V . . . . . . . . . . 110V
Lumen Output: . . 650lm. . . . . . . . . .1300lm . . . . . . . . 650lm . . . . . . . . . 1300lm
Min/Max Height: . 0.95/1.8mtr . . . . .0.95/1.8mtr . . . . . 0.95/1.8mtr . . . . . 0.95/1.8mtr
2. INTRODUCTION
3. SPECIFICATION
4. GENERAL INSTRUCTIONS
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal,
drain off any fluids (if applicable)into approved containers and dispose
of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
Mounted in die-cast aluminium housings. Feature 18SMD LEDs which give 120° spread of light, longer working life and lower running costs than traditional halogen
bulbs. Suitable for lighting workshops and garages. Supplied with mains cable and BS approved plug.