Model No
: . . . . . . . . . . . . .
HVF16
. . . . . . . . . . . . .
HVF18.V3
Fan Diameter: . . . . . . .400mm(16”) . . . . . . . . . . . 450mm(18”)
Speeds: . . . . . . . . . . . . . . . . . . . .3 . . . . . . . . . . . . . . . . . . . . 3
Motor Power: . . . . . . . . . . . . .80W . . . . . . . . . . . . . . . . . 90W
Supply: . . . . . . . . . . . . . . . . .230V . . . . . . . . . . . . . . . . . 230V
Current: . . . . . . . . . . . . . . . . .0.3A . . . . . . . . . . . . . . . . . 0.5A
"
WARNING! Ensure that you read, understand and apply safety instructions in
Section 1 before using fan.
3.1.
Check that the speed control is set to “0” (off) and then plug into the mains power
supply and switch the power on.
3.2.
The fan features 3 speeds which are selectable using the control buttons located
at the back of the fan above the motor. See Fig.4. LOW (1) or MED (2) settings will
suit most needs, HIGH (3) is used for maximum air movement.
3.3.
Adjust the direction of the air flow by moving the base from side to side and tilting
the fan up or down.
3.4.
When you have finished using the fan ensure you turn the speed control switch to
“0” (off) and disconnect the fan from the mains power.
"
"
WARNING! Ensure that the fan is disconnected from the mains power supply
before attempting any of the following:
4.1.
Use a soft, damp cloth to clean the fan.
DO NOT immerse the fan in water and never allow water to drip onto the motor housing.
DO NOT use solvents, petroleum, paint thinner or other chemicals to clean the fan.
4.2.
To clean the fan blade, undo the screw B and remove the ring A which holds
the front and rear grilles together. Remove the front grille and clean the blade and
inside the grilles. Replace the front grille and refit the ring securing with screw B.
4.3.
Should the motor, speed control box or the power lead require service or
maintenance contact your local service agent.
4.4.
When not in use place the fan in its original box or otherwise cover to protect
from dust, and store in a safe, dry, childproof location.
3. OPERATION
4. CARE OF FAN
5. DECLARATION OF CONFORMITY
2. INTRODUCTION & SPECIFICATION
IND. HIGH VELOCITY PEDESTAL FAN
Models HVF16 & HVF18.V3
89/336/EEC EMC Directive
73/23/EEC Low Voltage Directive
93/68/EEC CE Marking Directive
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed below are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected, by a national authority,
upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
20th November 2006
Signed by Mark Sweetman
HVF16 & HVF18.V3 - 1 - 20/11/06
High velocity fans suitable for movement of huge volumes of air.
Carefully balanced and fully guarded blades provide quiet and safe
operation. Three-speed power selection and cradle stand allow
precise control of air flow to exactly where it is needed. Fitted with
BS approved plug. Suitable for use in industrial, commercial,
agricultural and automotive workshop and showroom applications.
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
Fig.4
