NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImPoRtAnt:
no liability is accepted for incorrect use of this product.
WARRAnty:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
www.sealey.co.uk
01284 757500
01284 703534
Original Language Version
© Jack sealey limited
environmental Protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Weee Regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
Parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
GsA04,GsA05,GsA06 | issue 1 31/10/16
5. mAIntenAnce
8
do not
use petrol, solvent, or other flammable liquids for cleaning of tool.
solvents used for cleaning the tool handle and tool body can
cause softening of seals. thoroughly dry the tool before starting work.
5.1.
in case of any abnormality in the tool operation, the tool should be immediately disconnected from the pneumatic system.
5.2.
All pneumatic system components must be protected from pollution. Pollution, which gets into the pneumatic system can harm
the tool and other elements of pneumatic system.
5.3.
maintenance of the tool before each use
5.3.1.
disconnect the tool from pneumatic system.
5.3.2.
Introduce a small amount of preservative fluid (for example wd-40) through the air inlet and
connect the tool to the pneumatic system
and run it for about 30 seconds. this will distribute the preservative liquid on the tool interior and clean it. disconnect the tool from
pneumatic system again.
5.3.3.
A small quantity of sAe 10 oil let into the tool interior via air inlet. it is recommended to use sAe 10 oil intended for maintenance of
pneumatic tools. connect the tool and run it for a short time. Wd - 40 may not serve as the appropriate lubricating oil. remove excess oil
5.3.4. every 6 months, or after 100 hours of work you should submit the tool for examination by a
qualified person.
A damaged / faulty tool can cause injuries. Any repair of the tool must be carried out by qualified person in an authorized repair workshop.
6. tRoUble sHootInG
failure
Possible solution
the tool speed is too slow
or it does not start
let a small amount of Wd-40 through the air inlet. run the tool for a few seconds. the blades may stick to the
rotor. run the tool for about 30 seconds. lubricate the tool with small amount of oil. Attention! the excess of oil
can cause a decrease in power of tool. in this case, you should clean the drive.
the tool starts and then
slows down
the compressor does not provide enough air. the tool starts by the air collected in the tank of compressor. As
the tank is emptying, the compressor has not kept pace with the refilling of air shortages. Connect the device
to a more efficient compressor.
Insufficient power
Make sure that the air hoses have an internal diameter as specified. Check the air pressure, whether it is set
to the maximum value. make sure that the tool is properly cleaned and lubricated. in the absence of results,
submit the tool for repair.
