DO NOT
operate tool where there are flammable liquids or gases.
DO NOT
hold unsecured work in your hand.
DO NOT
get the tool wet or use in damp or wet locations.
DO NOT
leave the tool running unattended.
NOTE
: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
Multipurpose high-speed power tool with on/off and electronic variable speed controls. Stepless control between 10,000 and 32,000rpm. Spindle
lock for fast tool changes. Supplied with a full range of tips, wheels, sanding discs/bands, dressing stone, chuck spanner and flexible rotary
shaft. Suitable for carving, shaping, de-burring, drilling, engraving, cutting and tool sharpening. Supplied in carry-case.
3. SPECIFICATION
Model No:
.................................................................................................................................
E540.V3
Motor Power - Supply .........................................................................................................
135W - 230V
Speed Range ...........................................................................................................10000 to 32000rpm
Collet Capacities .......................................................................................................... 2.3mm and 3mm
Twist Drills .................................................................................................................... 2.3mm and 3mm
Mounted Points ..............................................................................................................................10pcs
Diamond Tipped Engraving Heads...................................................................................................2pcs
Sanding Cylinder .......................................................................................................... 12.7mm x 15mm
Accessories ....................................................... Sanding bands (4pcs), Sanding discs (3pcs), Spanner
Cutting Discs (8pcs), Polishing Wheels (4pcs) Dressing Stone
4. CONTENTS
5. OPERATION
5.1.
Fitting Accessories
5.1.1.
Ensure the tool is switched off and unplugged from the mains supply.
5.1.2.
Press the spindle lock button and slowly turn the collet nut until the spindle lock engages. Refer to Fig.1.
5.1.3.
Retain pressure on the spindle lock button and turn the collet nut anticlockwise to open the collet.
NOTE: Never press the spindle lock button when the tool is running.
5.1.4.
The required accessory may now be fitted into the collet. Fully insert the accessory shaft to reduce the risk of bending in use.
Tighten the collet nut firmly. Finally, release the spindle lock button.
3.1 Refer to fig.1 and 2.
1) 10 Point Grinding wheel set. ..................... E540.V2-ACC1
2) Spherical diamond cutter. ......................... E540.V2-ACC2
3) Tapered diamond cutter. ........................... E540.V2-ACC3
4) Mandrel for felt wheel. .............................. E540.V2-ACC4
5) Mandrel for cut-off wheel. ......................... E540.V2-ACC5
6)
HSS twist drill (2.3mm) .............................
E540.V2-ACC6
7) HSS twist drill (3mm). ............................... E540.V2-ACC7
8) Cut-off wheels. .......................................... E540.V2-ACC8
9) Sanding discs (20 x 0.35mm). ...................... E540.V2-ACC9
10)
Sanding band (12.7 x 12.7mm). ..........................E540.V2-ACC10
11)
Sanding shank (12.7 x 12.7mm). ...............................E540.V2-ACC11
12)
Spanner (9.7mm). ...................................E540.V2-ACC12
13)
Brass collet (2.3mm).
..............................E540.V2-ACC13
14)
Flexible drive locking bar. ........................E540.V2-ACC14
15)
Felt wheel (22 x 7mm). ............................E540.V2-ACC15
16)
Felt wheel 12.7 x 7mm).
..........................
E540.V2-ACC16
17)
Dressing stone (20 x 10 x 10mm). .......................E540.V2-ACC17
18)
Flexible extension drive. ..........................E540.V2-ACC18
19)
Motor unit. ........................................................E540.V3-G
Fig. 1
Fig. 2
E540.V3 Issue: 3(4) - 03/09/18
Original Language Version
© Jack Sealey Limited
