4.5.
BULK FILLING
4.5.1.
Press the catch plate to release the plunger handle.
4.5.2.
Connect a low pressure bulk greasing unit to the bulk filler nipple at the top of the gun and fill until plunger is fully extended.
4.5.3.
Press and hold the catch plate and push the plunger handle down until some resistance
is felt.
4.5.4.
Open the pressure release valve until grease appears.
4.6.
PRIMING THE GUN
4.6.1.
Before loading the gun with a cartridge or filling via a grease bucket, it is ideal to prime
the gun.
4.6.2.
To prime the gun simply pack grease into the cavity located at the entrance of the gun
assembly (where the grease tube screws into the gun) and operate the trigger,
this will induce the intake of grease into the gun assembly.
4.7.
OPERATION
8
DO NOT
tamper with the relief valve (fig.4.5). To do so may cause damage to the gun
and will invalidate the warranty.
4.7.1.
To operate the gun simply push the grease outlet onto the grease nipple and operate the
trigger until the desired amount of grease has been delivered.
4.7.2.
If you encounter air pockets during operation simply exert force on the plunger (Fig 4.1),
press the pressure release valve (Fig 4.2) and operate trigger (Fig 4.3) in short, sharp
bursts until grease begins to flow from the nozzle.
4.7.3.
When the grease gun is not in use turn the locking button (Fig 4.4) to the “lock” position
4.7.4.
To check the remaining battery power, press and hold down the LED display button on the top of the grease gun. A gauge will appear
on the display, showing the percentage of battery charge left.
5. TROUBLESHOOTING
fig.4
Condition
Possible Cause
Corrective Action
Motor fails to run.
- Battery needs recharging.
- Faulty wiring to motor.
- Recharge battery.
- Remove battery, disassemble handle and
check wiring for loose connections.
Pressure release valve opens to
discharge grease.
- Blocked line.
- Blocked bearing.
- Blocked grease fitting.
- Check lines, pipe joints and grease
fittings and remove any obstructions.
Grease gun fails to dispense grease. - Grease tube is out of grease.
- Loss of prime.
- Check valve is not functioning.
- Check that the tube contains grease.
- Repeat priming operation.
- Remove check valve, clean and inspect
the valve seat.
Grease gun continues to lose prime.
- Air may be trapped in locations throughout the
grease tube ass’y after bulk filling.
- Grease tube follower may be binding.
- Empty grease tube ass’y, refill and repeat
priming operation.
- Replace grease tube ass’y.
Battery fails to charge.
- Charger may not have power.
- Battery may be dead.
- Check the mains charger is providing
power.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [email protected] or 01284 757505.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
CPG12V.V4 Issue 1 07/08/2020
Original Language Version
© Jack Sealey Limited
