Condition
Possible Cause
Corrective Action
Motor fails to run.
- Battery needs recharging.
- Faulty wiring to motor.
- Recharge battery.
- Remove battery, disassemble
handle and check wiring for loose
connections.
Pressure release valve opens to
discharge grease.
- Blocked line.
- Blocked bearing.
- Blocked grease fitting.
- Check lines, pipe joints and
grease fittings and remove any
obstructions.
Grease gun fails to dispense
grease.
- Grease tube is out of grease.
- Loss of prime.
- Check valve is not functioning.
- Check that the tube contains
grease.
- Repeat priming operation.
- Remove check valve, clean and
inspect the valve seat.
Grease gun continues to lose
prime.
- Air may be trapped in locations
throughout the grease tube ass’y
after bulk filling.
- Grease tube follower may be
binding.
- Empty grease tube ass’y, refill and
repeat priming operation.
- Replace grease tube ass’y.
Battery fails to charge.
- Charger may not have power.
- Battery may be dead.
- Check the mains charger is
providing power.
3.5.2 Connect a low pressure bulk greasing unit to the bulk filler nipple at the
top of the gun and fill until plunger is fully extended.
3.5.3 Press and hold the catch plate and push the plunger handle down until
some resistance is felt.
3.5.4 open the pressure release valve until grease appears.
3.6 PRIMINg ThE guN
3.6.1 Before loading the gun with a cartridge or filling via a grease bucket, it is
ideal to prime the gun.
3.6.2 To prime the gun simply pack grease into the cavity located at the
entrance of the gun assembly (where the grease tube screws into the
gun) and operate the trigger, this will induce the intake of grease into
the gun assembly.
3.7 OPERATION
WARNINg: DO NOT
tamper with the relief valve (fig.4.5). To do so may cause
damage to the gun and will invalidate the warranty.
3.7.1 To operate the gun simply push the grease outlet onto the the grease
nipple and operate the trigger until the desired amount of grease has
been delivered.
3.7.2 If you encounter air pockets during operation simply exert force on the
plunger (Fig 4.1), press the pressure release valve (Fig 4.2) and operate
trigger (Fig 4.3) in short, sharp bursts until grease begins to flow from the nozzle.
3.7.3 When the grease gun is not in use turn the locking button (Fig 4.4) to the “lock” position
3.7.4 To check the remaining battery power, press and hold down the LED display button on the top of the grease gun.
A gauge will appear on the display, showing the percentage of battery charge left.
4. TROuBLEShOOTINg
Fig 4
01284 757500
01284 703534
Sole uK Distributor, Sealey group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
NOTE:
It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of
products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance
scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable) into
approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the Eu Directive on Waste Electrical and
Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling information.
© Jack Sealey Limited
Original Language Version
CPG12V.V3 Issue:2(I) 08/12/16
