Remove jig saw, charger, blade and key from packaging and inspect. If any item is damaged or missing contact your supplier.
Note:
When new, the battery will have been shipped in a low charge state. It will take longer to charge the battery initially and several subsequent
charges may also take a little longer than when the battery reaches its optimum performance.
3.1.
Charging the battery pack.
In the interest of long battery life, recharge the NiCd battery promptly. Recharging is always necessary when the power of the jig saw starts to decrease. Never
allow the battery to discharge completely as this will cause a defect in the battery.
3.1.1. To remove the battery pack from the saw, depress the two side clips (fig.1 item A). Do not touch the metal battery terminals.
3.1.2. Place saw in the case and remove the battery charger.
3.1.3. Stand the charger on a safe flat surface and connect to the mains.
3.1.4. The battery is designed to fit into the charger one way only. This is to ensure that the positive (+) and negative (-) polarities correspond.
Align the + and - polarity marks on the base of the battery with the + and - marks on the charger, insert the battery and press very
slightly downward to seat the battery firmly into the charging base (fig.2).
p
WARNING!
DO NOT try to force battery into the base with crossed polarities.
3.1.5. The red charge light will come on when the battery is inserted into the charger. Under normal conditions a flat battery will take 1 hour to fully
charge at which point the green light will come on. The temperature of the battery may rise slightly during the charging operation. This is normal.
Note:
There is no automatic switch-off when the battery is fully charged - turn off charger/remove battery to prevent battery damage from over-charging.
3.1.6. If the battery fails to charge, check:
1) Whether there is voltage at the socket outlet.
2) Whether there is good, clean contact between the charger and battery terminals.
3.1.7. Remove the battery from the charger and both lights will go out. Switch off and unplug the charger. Push the battery into the saw base
until it snaps into place. The saw is now ready for use.
3.1.8. Place the charger back in the carry case.
Note:
Attempting to charge a battery immediately after use may result in the red charging light not coming on. If so, allow the battery to cool
and try again.
3. OPERATING INSTRUCTIONS
2. SPECIFICATIONS
Motor . . . . . . . . . . . . . . . . . . . . . . . . .12V
Full charge time . . . . . . . . . . . . . . . .1 hour
Blade stroke . . . . . . . . . . . . . . . . . . .16mm
Stroke rate . . . . . . . . . . . . . . . . .2800 spm
Blade length . . . . . . . . . . . . . . . . . .100mm
Cutting capacity - wood . . . . . . . . . .50mm
- metal . . . . . . . . . . .3mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . .2kg
Items packed in carton
1. Carry case
2. Cordless jig saw with battery
3. Battery charger
4. Saw blade
5. Hex. key (for blade clamp screw)
fig. 2
1.4.
BATTERY CHARGER SAFETY INSTRUCTIONS
p
WARNING!
DO NOT use the charger to charge any battery other than that supplied for the saw. Other types of batteries may explode!
3
All mains electrical supply safety features must be followed as described in 1.3. above.
3
Disconnect the charger from mains power supply when not in use.
3
Store the charger in the same manner as battery, see para. 1.2.
7
DO NOT expose the charger to damp or wet conditions. The charger is for indoor use only.
7
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Contact an authorised service agent.
7
DO NOT dismantle the charger as this may cause damage or personal injury and will invalidate your warranty.
7
DO NOT attempt to connect two chargers together.
7
DO NOT insert foreign objects or material into the hole reserved for the battery.
7
DO NOT force the battery into the charger. The battery will only fit one way to ensure correct polarity alignment.
7
DO NOT immediately charge a second battery. Consecutive charging will overheat the charger. Allow the unit to cool for 15 minutes before
charging the next battery.
CP9912VJ - 0064 - (1) - 040699
3
Important: Check that the voltage marked on the charger is the same as the power supply to be used.
3
Uncoil the cable between the charger and plug before use.
7
DO NOT pull or carry the charger by the cable, or use the cable to pull the plug from the mains socket.
fig. 1
A
Spare Battery
Order part no: CB12/98
Note:
This battery also fits Cordless
Hammer Drill model CP9812VHK.
red -
charging
indicator
green -
fully charged
indicator
