2. INTRODUCTION
C
ordless 20V pruning shears - body only. Power assisted pruning shears makes pruning stems and branches quick and easy. Cuts through
thin and thicker branches up to 25mm. Brushless motor which gives improved performance and requires less maintenance than the brushed
equivalent, making a more efficient, longer lasting tool. Additional safety switch for extra protection. Ergonomic and lightweight in design, this tool
makes a great addition to your garden equipment. Requires compatible 20V battery and mains charger, sold separately.
3. SPECIFICATION
Model: ............................................................................CP20VPS
B
attery ............................
20V 2Ah - 6Ah Lithium-ion (not included)
C
onsumable parts
.................................
CP20VBP2 - 2Ah Battery,
.......................
CP20VBP4 - 4Ah Battery, CP20VBP6 - 6Ah Battery
Replacement parts ........
CP20VMC - Mains Charger (not included)
Blade Length
.........................................................................
30mm
R
unning Time:
............
2Ah - 25mins, 4Ah - 45mins, 6Ah - 60 mins
Voltage:
..............................................................................
20V DC
4. FEATURES
1. Lower shear blade
2. Upper shear blade
3. Hex Screw
4. Switch Trigger
5. Blades tightening nut
6. Button of Battery Pack
7. Battery Pack
8. On/Off switch (I/O)
1
2
4
6
7
8
3
5
Original Language Version
© Jack Sealey Limited
C
P20VPS Issue 1 09/09/21
5. OPERATION
5.1.
TURN ON
5.1.1.
Insert the battery pack.
5.1.2.
Hold the shears firmly, and slide the I/O switch to the “I” (on) position. The tool makes a single beep to indicate that the I/O switch
has been on the “I” (on) position.
5.1.3.
The shear blades are in locked-mode when the I/O switch is on. To release the lock, depress the switch trigger two times. The upper
shear blade opens automatically.
5.1.4.
To close the shear blade, depress the switch trigger once again.
5.2.
TURN OFF
5.2.1.
Depress down and hold on the switch trigger for about three seconds and then the tool makes two ticking sounds.
5.2.2.
Slide the I/O switch to the “O” (off) position. The tool makes continuous ticking sound to indicate that the I/O switch has been moved to
the “O” (off) position.
5.2.3.
Remove the battery pack.
5.3.
ACCIDENTAL RE-START PREVENTIVE FUNCTION
5.3.1.
Even if the battery pack is inserted and switch trigger is pressed when the I/O switch is locked on the “I (ON)” position and the
shear blades are on unlocked-mode with the battery removed, the tool does not start to prevent accidental operation. To start the tool,
depress the switch trigger two times and then depress the switch trigger once.
5.4.
AUTO LOCKED-MODE AND SHUT-OFF MODESHIFT
5.4.1.
For safety reasons, the tool shifts into shut-off mode automatically if the tool is left untouched for approximately 10 minutes: The tool
is shift into shut-off mode. Slide the I/O switch to the “O” (off) position once and slide the I/O switch to the “I” (on) position again, then
depress the switch trigger two times to release the lock.
5.5.
PRUNING OPERATION
5.5.1.
Cut branches one by one. The maximum thickness of branches which can be cut with these shears is about 30mm. Maintain
proper footing and balance at all times.
5.5.2.
AFTER USE
5.5.3.
Close the shear blades, press the I/O switch to the “O” (off) position, and remove the battery pack. Store the shears in dry, high or
locked-up place out of reach of children.
