8
DO NOT
try to open or dismantle the charger.
8
DO NOT
get the charger wet, or use in wet, damp conditions (for indoor use only).
8
DO NOT
operate the charger if it or the battery is damaged.
8
DO NOT
insert foreign objects or material into the hole reserved for the battery.
8
DO NOT
force the battery into the charger. The battery will only fit one way to ensure correct polarity alignment.
8
DO NOT
charge a second battery immediately. Consecutive charging will overheat the charger. Allow the unit to cool for 15 minutes
before charging the next battery.
9
Store the charger in the same manner as the battery, see section 1.2.
1.4.
GENERAL SAFETY.
9
Maintain the Ratchet Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the Ratchet Wrench is switched off before installing the battery pack.
9
Keep the Ratchet Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Ratchet Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
water piping
9
Ensure battery pack is correctly inserted into the Ratchet Wrench handle and latched in place before attempting to switch on
Ratchet Wrench.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this Ratchet Wrench
does not need to be plugged into the mains power.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the Ratchet Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the
Ratchet Wrench
.
8
DO NOT
operate the
Ratchet Wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the
Ratchet Wrench
operating unattended.
8
DO NOT
carry the
Ratchet Wrench
with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT
use the
Ratchet Wrench
for a task it is not designed to perform.
8
DO NOT
operate the
Ratchet Wrench
when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the
Ratchet Wrench
or battery charger wet or use in damp or wet locations.
2. INTRODUCTION
Compact, lightweight cordless ratchet wrench, allows access to tight spaces. Variable speed control trigger with lock function gives more
control during application. Heavy-duty mechanical steel ratchet head with forward and reverse control. Robust composite housing with soft,
comfortable grip. Integrated LED battery level indicator and LED work light. Requires Model No CP1200BP 12V 1.5Ah Lithium-ion battery and
Model No CP1200MC battery charger.
3. SPECIFICATION
Model No.. .................................................................
CP1202
B
attery options (not included)
12V 1.5Ah Li, 12V 3Ah Li, 12V 4Ah Li
Consumable parts:
C
P1200BP
................................................
Battery 12V 1.5Ah
C
P1200BP3
.................................................
Battery 12V 3Ah
C
P1200BP4
.................................................
Battery 12V 4Ah
Replacement parts .....................
CP1200MC - mains charger
Drive ............................................................................
3/8”sq
Max. torque ...................................................... 45Nm(33lb.ft)
No load speed .........................................................
0-250rpm
N
oise power/pressure
........................................
100/88dB(A)
V
ibration/uncertainty
........................................
2.898/1.5m/s²
4. CHARGING
4.1.
BATTERY PACK REMOVAL AND REPLACEMENT
4.1.1.
Switch the machine off before removing the battery pack.
4.1.2.
Press the battery latches in (located either side of grip
and withdraw the battery pack (fig.1).
4.1.3.
To replace the battery pack, push the stem into the drill
until the latches engage. The battery pack can only be
inserted in the correct orientation.
4.2.
BATTERY CHARGING
4.2.1.
Batteries that have been out of use for some time or are new
may not accept a full charge. This is not a battery fault; the
battery may need to be discharged and charged a couple of
times to restore full capacity.
4.2.2.
Connect the charger to the electric power supply. A flashing
green LED will show.
4.2.3.
Insert the battery into the charger. A steady red light
will show.
fig.1
Original Language Version
© Jack Sealey Limited
C
P1202 | Issue 2 (1F) 05/03/20
