© Jack sealey limited
Original Language Version
5.2.4.
Hold grinding stone firmly. to protect your hands use cloth or wear gloves. unscrew retaining nut (fig.7.1)
Note:
The
nut
on
the
right
side
of
the
grinder
has
standard right
hand
thread
(undo
anti-clockwise).
the left side nut has a left hand thread and must be loosened by turning clockwise. it may be necessary
to strike the wrench sharply in the loosening direction with the heel of your hand to loosen the nut.
5.2.5.
Remove grinding stone
washer
(fig
7.2),
blotter
(3),stone (4),
2nd
blotter
(5),
washer
(6)
from
main
spindle (7).
5.2.6.
carefully inspect the new stone before installing to ensure there are no fissures, chips, or cracks.
Warning! dO nOt uSe a damaged StOne.
5.2.7.
inspect the blotters, if they are damaged replace them. the grinder must never be used without stone
blotters, should you not have any available when you need to replace them, cut out a piece of suitable
cardboard the same shape for temporary use only.
5.2.8.
Install
the
new
stone
by
reversing steps
above.
Ensure
washers (2
&
6)
are
installed with
the
flange on the outside, (i.e. the concave
side against the blotter).
5.2.9.
Hold stone steady and secure locking nut.
dO nOt
over tighten as this may crack the stone. 5.2.10.
replace stone
cover,
re-adjust tool
rest
to
a
maximum of
2mm
from
stone
face
and
tighten
securely.
note:
You do not require a certificate to
change a wire wheel. Assembly is the same as with a stone.
6.1.
pre use inspection.
note:
use the same clearance and alignment information if your model has a wire brush.
Warning!
INSPECT THE
GRINDER
BEFORE OPERATING
THE
MACHINE.
ENSURE THE
GRINDER
is unPluGGed from THE
MAINS
POWER BEFORE COMMENCING
THE
INSPECTION.
6.1.1.
check the tool rests are securely fixed and set at a maximum of 2mm from the grinding stone.
6.1.2.
check that eye shields are in good condition, are secure and that you can see through them clearly.
6.1.3.
turn the grinding stones by hand and check for any damage. check they do not touch the tool rests and are correctly aligned.
if any of the above checks fail, replace, repair, or adjust as necessary before starting the grinder.
6.2.
Stone use.
depending on the model, grinders are supplied with one or two aluminous oxide stones. stones have two grades, fine are preferred
for hard materials and a coarse stones for soft materials.
When
grinding, should
surface
of
the
stone
become
“loaded” (coated with
particles of
the
material being
ground) it
is
probably the
wrong grade of stone for the job.
important reminder: Grinding stones
muSt
only be assembled by a person holding a grinding wheel certificate.
section 5.
6.3.
using the grinder
.
Warning!
Before
commencing
work,
ensure
you
have
read,
understood,
and
apply
the
section
1.
Safety
Instructions
Plug grinder into the mains power supply. Place the eye shield in its appropriate
safety location.
switch the grinder on, and bring the work piece slowly into contact with the spinning stone, or wire wheel.
When you
have
completed
your
task,
unplug
the
grinder
from
the
mains
power
supply,
and
clean
the
machine ready
for
next
use.
7.
maintainance
Warning!
ensure the grinder is unplugged from the mains power supply before performing any maintenance or service.
7.1.
As the grinding stone wears, adjust the position of the tool rests. the rest must be at a maximum of 2mm from the stone surface.
7.2.
regularly remove the grinding stone covers and clean out any dust and dirt.
7.3.
the machine motor and bearing are sealed units and require no regular maintenance. should you require assistance, contact your
local sealey service agent.
7.4.
for information relating to the handling and maintenance of grinding stones refer to section 5.
parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When
the
product becomes completely
unserviceable
and
requires disposal, drain
off
any
fluids
(if
applicable) into approved containers and dispose of the product
and the fluids according to local regulations.
Weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
6.
OperatiOn