© Jack sealey limited
Original Language Version
instructions for
bench grinder
Ø
200mm 600W/230V heaVy-duty
model no:
bg200/99.V3
thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to
Wear
eye
Wear
a
mask
Wear
ear instructions
protection protection
1.
Safety
1.1.
electrical Safety
Warning!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if used in the course of business duties, it must be
maintained in a safe condition and routinely PAt (Portable Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Ensure that
the
voltage
rating
on
the
appliance suits
the
power
supply
to
be
used
and
that
the
plug
is
fitted
with
the
correct
fuse
-
see
fuse rating in these instructions.
dO nOt
pull or carry the appliance by the power cable.
dO nOt
pull the plug from the socket
by the cable.
dO nOt
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired
or replaced immediately by a qualified electrician.
This
product is
fitted
with
a
BS1363/A
13
Amp
3
pin
plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure
that
repairs
are
carried
out
by
a
qualified
electrician.
Replace a
damaged plug
with
a
BS1363/A
13
Amp
3
pin
plug.
If
in
doubt
contact
a
qualified electrician.
a) Connect the
GREEN/YELLOW earth
wire
to
the
earth
terminal
‘E’.
b) Connect the
BROWN live
wire
to
the
live
terminal
‘L’.
c) Connect the
BLUE
neutral
wire
to
the
neutral
terminal
‘N’.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey
recommend
that
repairs
are
carried
out
by
a
qualified electrician.
1.2.
general Safety
Warning!
disconnect the grinder from the mains power, and ensure the grinding wheels are at a
standstill before
attempting to change accessorie
s, service or perform any maintenance.
note:
With
the
exception of
“Abrasive Wheels Regulations”’
safety
instructions
will
also
apply
to
use
of
a
wire brush on appropriate models.
maintain the grinder in good condition and check moving parts alignment regularly.
replace or repair damaged parts. use recommended parts only. non authorised parts may be dangerous and will invalidate the
warranty.
▲
danger! dO nOt
use a damaged stone as it is dangerous and may cause damage or serious personal injury.
Warning!
Only
persons qualified under
the
“Abrasive Wheels Regulations”
and
holding
a
current
grinding wheel
certificate are to change
or
dress
grinding stones.
Unplug
grinder
from
mains
power
and
refer
to
chapter 4
“Grinding Stones” for
details.
Warning!
Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
A guard or
any other part that is damaged should be repaired or replaced before tool is used. the safety guard is a mandatory fitting
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
recommended fuse rating
5
Amp
