![background image](http://html.mh-extra.com/html/sealey/adt7-v2/adt7-v2_quick-start-manual_1225100001.webp)
ADJUSTABLE GEARBOX SUPPORT 500KG
CAPACITY SUITABLE FOR MODELS 300ETJ.V2
AND 500ETJ.V2
MODEL NO:
ADT7.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure all preliminary checks are carefully carried out before using gearbox support and transmission jack.
WARNING! Follow all of the safety instructions issued with the transmission jack.
WARNING!
Ensure load is placed level and centrally on gearbox support and is fixed in place before attempting to lift, lower, or
transport load. Always use load restraint chains and attachments to stabilise and secure the load to the gearbox support.
9
Before use ensure the transmission weight and size
DO NOT
exceed the capacity of the gearbox support or the transmission jack.
9
The gearbox support is heavy, care should be taken when placing onto the transmission jack.
9
Ensure that the sliding bracket and chain mount bracket nuts and bolts are fully tightened when the gearbox support is loaded.
9
Care should be taken when using the gearbox support and vertical transmission jack in conjunction with a vehicle lift to ensure that the
vehicle is not lowered whilst the jack is in position.
9
Before storing ensure gearbox support is clean and free of grease and oil.
9
Store in a safe, dry childproof location.
8
DO NOT
use the gearbox support without restraint chains.
8
DO NOT
replace the chains with an inferior form of restraint.
8
DO NOT
allow untrained persons to use the gearbox support.
8
DO NOT
move the transmission jack, with or without a load, with the gearbox support in the raised position.
8
DO NOT
use the gearbox support for any purpose other than for vehicle transmissions.
2.
i
INTRODUCTION
Fully adjustable saddle with forward, backward and side to side tilt. Suitable for use with Model Nos: 300ETJ.V2 and 500ETJ.V2.
3.
i
SPECIFICATION
Model No: .................................................................ADT7.V2
Capacity: ...................................................................... 500kg
Compatibility: ....................................300ETJ.V2, 500ETJ.V2
Net weight ................................................................. 12.02kg
4. ASSEMBLY
WARNING!
Failure to assemble the gearbox support correctly may result in serious damage and/or personal injury. Unpack
the product and check contents against the contents list. Should there be any damaged or missing parts contact your supplier
immediately.
4.1.
ASSEMBLY
(refer to fig.1)
4.1.1.
Position the support plate (2) on a flat surface with the bracket facing upwards. Place the main support (1) over the support plate (2) so
that the bracket fits into the slot on the main support (1).
Refer to
instruction
manual
Wear protective
gloves
Wear protective
clothing
Wear safety
footwear
Item
Description
Qty Item
Description
Qty
1
Main Support
01
10
Flat Washer
06
2
Support Plate
01
11
Spring Washer
10
3
Adjuster Screw
02
12
M10 Nut
10
4
Pivot Pin
01
13
Circlip
02
5
Sliding Bracket
02
14
Split Pin
01
6
Chain Mount Bracket
04
15
Chain
02
7
M8 Bolt and Nut
02
16
Retaining Bolt
02
8
Chain Hook
02
17
Reduction sleeve
01
9
M10 x 30mm Bolt
06
fig.1
ADT7.V2 Issue 3 (H, F) 07/09/18
Original Language Version
© Jack Sealey Limited