9
ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of
the stand. exercise extra care when using with a three wheeled vehicle or a trailer. Refer to vehicle manufacturer’s
instructions.
9
once vehicle is supported, ensure that the vehicle and stands are stable before starting work. ensure that it is not
possible for the vehicle to move before commencing any work.
9
Inspect stands before each use.
do noT
use if they show signs of damage.
do noT
use if it is suspected that they
have been overloaded.
9
Before commencing any work or going beneath the vehicle, undertake a risk assessment. ensure that a responsible
person is aware of the work about to be undertaken.
9
Replace any labels on the axle stand should they become unreadable. This applies in particular to any warning or
operation instruction labels. If replacement labels are required, contact your Sealey stockist.
8
do noT
use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
8
do noT
push or twist the vehicle/load whilst it is supported on stands.
8
do noT
mix components between stands. Use only as supplied.
8
do noT
allow children or animals in the vicinity of a vehicle supported on axle stands.
8
do noT
leave a vehicle on axle stands in an area that could be considered a hazard to others or property.
9
folloW STePS 1, 2, and 3 To correcTly Place VeHicle / load onTo axle STandS.
2. inTroducTion
Single-piece hydraulic unit with heavy chassis design and large jacking saddle (pad available as optional extra - model no. JP14). Universal
joint release mechanism allows safer, more controlled lowering of the jack. Twin piston Super Rocket lift feature brings lifting arm straight into
contact with the jacking point. Polyurethane wheels for smoother manoeuvrability and helps prevent damage to workshop floor. Fitted with safety
overload valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5tonne GVW.
Supplied with Ratchet Type Axle Stands, 3tonne (3000kg) capacity per stand (6tonne (6000kg) per pair). min./max. Working Height: 285/420mm.
Angled teeth in cast iron support posts - the more weight applied, the tighter the post is locked.
3. SPecificaTion
Model no:
. . . . . . . . . . . . . . . . . . . . . . .
3015cxHV
Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3tonne
minimum Saddle Height:. . . . . . . . . . . . . . . . 132mm
maximum Saddle Height: . . . . . . . . . . . . . . . 472mm
maximum Chassis Height: . . . . . . . . . . . . . . 158mm
length: . . . . . . . . . . . . . . . . . . . . . . . . . . . 620mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31kg
Consumable Parts: . . . . . . . JP13 - Rubber Jack Pad
4. oPeraTion - Jack
4.1.
before firST uSe.
4.1.1.
Assemble the handle by lining up the holes in the two-piece handle and fasten with the assembly screw.
4.1.2.
loosen location bolt at the back of the handle base. Insert the jack handle and tighten the bolt.
4.1.3.
Before using jack, purge the hydraulic unit in order to eliminate any air in the system. open the valve by turning the handle
anti-clockwise (fig.1), and pumping 8 or 9 times. When complete, close the release valve by turning the handle fully clockwise (fig.1).
4.1.4.
Place a few drops of hydraulic jack oil onto the pump piston and pump the handle several times to distribute the oil. Thoroughly
lubricate all moving parts.
General JackinG.
WarninG!
Before lifting ensure Section 1 safety instructions are read and understood.
4.1.5.
Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which the jack is to stand is level and solid (not
tarmacadam) and use chocks under wheels of vehicle.
4.1.6.
Position the jack saddle under the vehicle manufacturer’s recommended lifting point.
4.2.
JackinG THe VeHicle.
4.2.1.
Turn the handle clockwise to close the release valve (fig.1)
and commence pumping handle up and down until the jack saddle reaches
the vehicle jacking point. Check the jacking point is centrally located on the saddle and continue to pump the handle to raise the vehicle.
4.2.2.
Should the jack become overloaded, a safety excess pressure valve will open and stop the jack from lifting.
WarninG!
The jack is a lifting device only and must not be used to support the load. Use correctly rated axle stands to support the load.
a
xle Stand Specification:
Capacity each: . . . . . . . . . . . . . . . . . . . . . . . . 3tonne
Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . 6tonne
minimum Working Height:. . . . . . . . . . . . . . . 285mm
maximum Working Height: . . . . . . . . . . . . . . 420mm
3015CXHV | Issue 2 (3) 07/02/19
Original Language Version
© Jack Sealey limited