Transmission Jack 1Tonne VerTical
Model no:
1000Tr
Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safeTy
WarninG!
ensure all preliminary checks are carefully carried out before use of jack. immediately repair or replace damaged
parts (use authorised service agent). ensure use of
genuine parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
WarninG!
Use jack on level and solid ground, preferably concrete. ensure the floor over which the jack will be transported is swept
clean.
▲
DanGer! Do noT
use on tarmacadam, or any other soft surface as jack may sink or topple. serious injury may result if ignored.
▲
DanGer!
if jack tips or leans sTop WhaT yoUr are DoinG. moVe QUickly To a safe DisTance. Do noT Try To holD
or sTeaDy Jack.
9
Use
jack in a suitable work area. Keep the area clean and tidy and free from unrelated materials. ensure there is adequate lighting.
9
Before use ensure the gearbox weight and size does not exceed the capacity of the jack.
9
ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack under the vehicle.
9
ensure the jack saddle is fully lowered and is clean, dry, and oil free before attempting to transport the jack with or without a load.
9
Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.
9
Maintain correct balance and footing. ensure the floor is not slippery and wear non slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/or tie back long hair.
WarninG!
ensure that the load is placed level and centrally on the jack saddle and that it is fixed in place before attempting to lift,
lower or transport the load.
9
The lowering speed will vary according to the weight of the load and the release valve setting.
9
diligence is required in ensuring that you continually monitor the operation until completed.
9
Should the jack make any abnormal sounds during use,
sTop
immeDiaTely
and contact your local service agent.
8
Do noT
operate the jack if any parts are damaged or missing.
8
Do noT
exceed the rated capacity of the jack.
8
Do noT
raise or lower vehicle lifting platform whilst the transmission jack is being used.
8
Do noT
transport the jack with, or without a load, with the saddle in the raised position.
8
Do noT
get the jack wet, or use it in damp or wet locations or areas where there is condensation.
8
Do noT
operate the jack when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do noT
lift or support vehicles with the jack and
Do noT
use the jack as a load-sustaining device.
8
Do noT
use the jack for any purpose other than removal, transportation and the installation of transmissions.
8
Do noT
make any modifications to the jack.
8
Do noT
adjust, or tamper with, the safety valve.
8
Do noT
remove any labels from the jack. If the labels are damaged or unclear, replace them.
8
Do noT
use brake fluid to top up the hydraulic unit. Use Sealey hydraulic oil only.
9
Use a qualified person to lubricate and maintain the jack.
9
Before storing the jack in a safe area, ensure that all parts are clean and free of grease and oil, especially the saddle.
2. inTroDUcTion
Manufactured to exacting standards, strong construction for durability and suitable for general workshop applications. Spring
loaded dead man’s safety release control reduces the risk of inadvertent lowering. Two way hydraulic unit ensures that the saddle
lowers at a controlled speed at all times, even without load. extra large castors allow for increased manoeuvrability. Hydraulic units
larger than the economy models for improved performance and durability. Can be fitted with optional Adjustable Gearbox Support -
check specification in table.
3. specificaTion
Rated capacity ..............................................................1000kg
Ram extensions ......................................................................1
Minimum saddle base height ......................................1120mm
Maximum saddle base height .....................................1950mm
Base size ............................................................610 x 680mm
F
ixed/Adjustable saddle
..................................................Fixed
optional accessories ...........
ADT5 adjustable gearbox support
1000TR Issue 3 (HF) 01/08/19
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Warning!
