Seagull SEA238 Скачать руководство пользователя страница 27

Страница: 27 / 33

Instruction Manual.

INSTALLATION PILOT AND

WINDSHIELD.

1) Locate items necessary to install pilot

and windshield.

2) A scale pilot is included with this ARF.

The Pilot included fits well in the cockpit.

(or you can order others scale pilot fig-

ures made by SG-Models. They are avail-

able at SG-Models distributors.).

If you are going to install a pilot figure,

please use a sanding bar to sand the base

of the figure so that it is flat.

Epoxy.

10mm

4) Position the windshield onto the fuse-

lage. Trace around the windshield onto

the fuselage using a felt-tipped pen. Cut

and remove the covering from between

the lines drawn, and glue the windshield

to the fuselage using epoxy or a special

canopy glue.

Epoxy.

3) Position the pilot figure on the cock-

pit floor as shown. Use epoxy to glue the

base of the pilot figure, please see pic-

tures as shown.

2) If all the decals are not precut, please

use scissors or a sharp hobby knife to cut

the decals from the sheet. Please be cer-

tain the model is clean and free from oily

fingerprints and dust. Position decal on

the model where desired, using the pho-

tos on the box and aid in their location.

INSTALLING BATTERY - RECEIVER.

1) Plug the five servo leads and the switch

lead into the receiver. Plug the battery

pack lead into the switch also.

2) Wrap the receiver and battery pack in

the protective foam rubber to protect

them from vibration.

1) If all the decals are precut and ready to

stick. Please be certain the model is clean

and free from oily fingerprints and dust.

Position decal on the model where de-

sired, using the photos on the box and

aid in their location.

APPLY THE DECALS.

Содержание SEA238


































Результаты поиска

Содержание SEA238

Отзывы:

Бренды по названию

Популярные бренды

Seagull SEA238, Инструкция по сборке

Результаты поиска

Содержание SEA238

Отзывы:

Бренды по названию

Популярные бренды