Seagull Models Sparrow Hawk SEA-93 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 22

background image

SPARROW HAWK

Instruction Manual

16

Masking tape.

Remove the covering.

INSTALLING THE HORIZONTAL STABILIZER.

Center line.

Hinge slot.

Pen.

Remove covering.

Epoxy.

When cutting through the covering to

remove it, cut with only enough pressure
to only cut through the covering itself. Cut-
ting into the balsa structure may weaken
it.

Epoxy.

«
...
14
15
16
17
18
...
»

Содержание Sparrow Hawk SEA-93























Отзывы:

Нет отзывов

Похожие инструкции для Sparrow Hawk SEA-93

Paradise AquaCraft

Бренд: Hobbico Страницы: 12

Бренд: Eduard Страницы: 4

Бренд: MTHTrains Страницы: 36

Бренд: Fisher-Price Страницы: 32

Barbie Babysitter

Бренд: Mega Bloks Страницы: 28

ZAG HEROEZ Miraculous Pixelo

Бренд: Lansay Страницы: 2

Ju 88A interior S.A.

Бренд: Eduard Страницы: 2

Super PNP F-100D Super Sabre

Бренд: Flex innovations Страницы: 32

1/48 KITTY HAWK KH80144 kit

Бренд: Eduard Страницы: 6

Бренд: Lionel Electric Trains Страницы: 8

Бренд: Trix Страницы: 24

Rabbit KS 100 SE Series

Бренд: Jet Central Страницы: 43

Бренд: GREAT PLANES Страницы: 53

Бренд: J-Power Group Страницы: 30

4-8-4 Northern Steam Locomotive and Tender

Бренд: Lionel Страницы: 12

Бренд: REVELL Страницы: 8

Бренд: Eduard Страницы: 4

Бренд: POLA G Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды