Seagull Models SEA230B Скачать руководство пользователя страница 2

Страница: 2 / 33

Skyraider

WARBIRD 10cc-15cc

Instruction Manual.

Thank you for choosing the

Skyraider

WARBIRD 10cc-15cc

ARTF by

SEAGULL MODELS

COMPANY LTD

,. The

Skyraider

WARBIRD 10cc-15cc

was designed with the intermedi-

ate/advanced sport flyer in mind. It is a semi scale airplane which is easy to fly and quick

to assemble. The airframe is onventionally built using balsa, plywood to make it stronger

than the average ARTF, yet the design allows the aeroplane to be kept light. You will find

that most of the work has been done for you already. The motor mount has been fitted

and the hinges are pre-installed. Flying the

Skyraider

WARBIRD 10cc-15cc

is simply a joy.

This instruction manual is designed to help you build a great flying earoplane. Please read

this manual throughly before starting assembly of your

Skyraider

WARBIRD 10cc-15cc

. User

the parts listing below to indentify all parts.

Please be awere that this aeroplane is not a toy and if assembley or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs offer a variety

of training procedures designed to help the new pilot on his way to successful R/C flight.

They will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

Содержание SEA230B


































Результаты поиска

Содержание SEA230B

Отзывы:

Похожие инструкции для SEA230B

Бренды по названию

Популярные бренды

Seagull Models SEA230B, Инструкция по сборке

Результаты поиска

Содержание SEA230B

Отзывы:

Похожие инструкции для SEA230B

Бренды по названию

Популярные бренды