manualshive.com logo in svg

Seagull Models Mini Nemsis EP, Инструкция по сборке

Поделиться
Скачать
Seagull Models Mini Nemsis EP Скачать руководство пользователя страница 15

15

www.seagullmodels.com

4) When you are sure that everything is

aligned correctly, mix up a generous amount of
Flash 30 Minute Epoxy.  Apply a thin layer to the
mounting slot and to bottom of the vertical sta-
bilizer mounting area.  Apply epoxy to the bot-
tom and top edges of the filler block and to the
lower hinge also.  Set the stabilizer in place
and realign.  Double check all of your measure-
ments once more before the epoxy cures. Hold
the stabilizer in place with T-pins or masking
tape and remove any excess epoxy using a
paper towel and rubbing alcohol.  Allow the ep-
oxy to fully cure before proceeding.

ELEVATOR - RUDDER  PUSHROD HORN

INSTALLATION.

 

1) Install the elevator control horn using

the same method as with the aileron control
horns.

 

2) Position the elevator control horn on

the both side of elevator.

Elevator control horn.

Rudder control horn.

Elevator control horn.

AILERON PUSHROD HORN INSTALLATION

85mm.

55mm.

60mm.

Elevator pushrod.

Rudder pushrod.

Elevator pushrod.

30mm.

Содержание Mini Nemsis EP




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды