manualshive.com logo in svg

Seagull Models HARRIER 3D .46, Инструкция по сборке

Поделиться
Скачать
Seagull Models HARRIER 3D .46 Скачать руководство пользователя страница 10

HARRIER 3D .46

                                                               

Instruction Manual.

10

 WHEEL AND WHEEL PANTS.

 

 1) Assemble and mounting the wheel pants

as shown in the following  pictures.

 

  

 2)  Follow diagram below for wheel pant

installation:

  

 3) You have to trim each axle using a toll

cutting and cut-off wheel.

Wheel Collar.

Axle.

Wheel.

Nut.

Wheel Pant.

Landing Gear.

Nut.

(2) Washer.

Caution when cutting the axles and wear

protective goggles.

46mm.

Slide the tank into the fuselage from inside so
that the neck is at the top of the fuselage and
it locates through the engine bulkhead. Gently
secure it to the top horizontal former with a
cable tie.

Blow through one of the lines to ensure
the fuel lines have not become kinked in-

side the fuel tank compartment.  Air should flow
through easily.

(2) Wheel Collar.

Axle.

Wheel.

Nut.

Nut.

(2) Washer.

10 mm.

Fuel tank.

Содержание HARRIER 3D .46





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды