manualshive.com logo in svg

Seagull Models Funfly 3D, Инструкция по сборке

Поделиться
Скачать
Seagull Models Funfly 3D Скачать руководство пользователя страница 22

SEAGULL FUNFLY 3D.                

                                                  

 Instruction Manual.

22

 

4)  Drill through the bottom of the rudder

with the 2mm drill.

 

5)  Using a toothpick insert a small amount

of the epoxy in the hole in the bottom of the
rudder. Insert the vertical tailwheel wire into the
hole with the epoxy and mount the nylon
brackets to the rudder with the hardware
included.

INSTALLATION PILOT AND CANOPY.

2

1

1)  Locate items necessary to install pilot, and
canopy.

2)  A scale pilot is included with this ARF. The
Seagull Pilot included fitting well to the cockpit.
(or you can order others scale pilot figures
made by Seagull factory. They are available at
Seagull distributors.)

3)  Position the pilot figure on the canopy floor
as show. Locate the oval shaped on the canopy
floor and remove the covering. Use epoxy to
glue this into the base of the pilot figure and
glue the cockpit panel in place with C/A glue,
please see pictures as shown.

If you are going to install a pilot figure, please
use a sanding bar to sand the base of the figure
so that it is flat.

M2 x 12mm.

C/A glue.

2

25mm.

1

M2 x 12mm.

2mm.

2mm.

C/A glue.

Содержание Funfly 3D

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды