manualshive.com logo in svg

Seagull Models EDGE 540, Инструкция по эксплуатации

Поделиться
Скачать
Seagull Models EDGE 540 Скачать руководство пользователя страница 19

www.seagullmodels.com

3

NOTE:

To avoid scratching your new aero-
plane we suggest that you cover your
workbench with an old towel. Keep a
couple of jars or bowls handy to hold
the small parts after you open the
bags.

Please trial fit all parts. Make sure you
have the correct parts and that they
fit and are aligned properly before
gluing! This will ensure proper as-
sembly as the  

EDGE 540 

is made

from natural materials and minor ad-
justments may have to be made.

The paint and plastic parts used in
this kit are fuel proof. However, they
are not tolerant of many harsh chemi-
cals including the following: paint
thinner, cyano-acrylate glue accel-
erator, cyanoacrylate glue de-bonder
and acetone. Do not let these chemi-
cals come in contact with the colours
on the covering and the plastic parts.

Please contact Horizon Hobby for product support and technical assistance at 

877-

504-0233

.  Replacement parts are available from your local dealer or through Horizon

Hobby.

HORIZON HOBBY DISTRIBUTIONS INC

4105 Fieldstone Rd, Champaign, IL 61822- USA

FOR USA MARKET ONLY.

Horizon Hobby, Inc. guarantees this kit to be free from defects in both material and workmanship
at the date of purchase. This warranty does not cover any parts damage by use or modification.
In no case shall Horizon Hobby’s liability exceed the original cost of the purchased kit. Further,
Horizon Hobby reserves the right to change or modify this warranty without notice. In that
Horizon Hobby has no control over the final assembly or material used for the final assembly,
no liability shall be assumed nor accepted for any damage resulting from the use by the user
of the final user-assembled product. By the act of using the user-assembled product, the user
accepts all resulting liability.

Once assembly of the model has been started, you must contact Horizon Hobby, Inc. directly
regarding any warranty question that you have. Please do not contact your local hobby shop
regarding warranty issues, even if that is where you purchased it. This will enable Horizon to
better answer your questions and service you in the event that you may need any assistance.
If the buyer is not prepared to accept the liability associated with the use of this product, the
buyer is advised to return this kit immediately in new and unused condition to the place of
purchase.

Horizon Hobby
4105 Fieldstone Road
Champaign, Illinois 61822
(217) 355-9511

Содержание EDGE 540






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды