manualshive.com logo in svg

Seagull Models DECATHLON, Инструкция по сборке

Поделиться
Скачать
Seagull Models DECATHLON Скачать руководство пользователя страница 12

DECATHLON 

                                                                                        

Instruction Manual

12

MOUNTING THE ENGINE

✑

1)Trial fit your engine on the motor mount.

The engine should be positioned so there is
ample clearance in the cowling for spinner
backplate mounted to the prop drive shaft.

✑

2)Marking 4 points on  the plastic motor

mount.

✑

3)Screw 4 pilot holes with 5 mm diameter.

✑

4) Your engine on the motor mount by

mounting with 4 bolts, 8 washers, and 4 nuts
provided.
A drop C/A glue on the bolt threads will help
prevent loosening in flight.

✑

  5) Attach the Z-Bend in the pushrod wire to

the throttle arm on the carburetor. You will need
to remove the throttle arm from the car-
buretor to be able to attach the Z-bend. When
complete, reattach the throttle arm to the car-
buretor.

 WHEEL  AND WHEEL PANTS

PARTS REQUIRED

Engine mount.

4MMx30MM.

Blow through one of the lines to ensure
the fuel lines have not become kinked

inside the fuel tank compartment.  Air should
flow through easily.

Pushrod wire.

112MM.

Exhaut hole needed to drill 20 - 30 mm
diameter.

Vent tube.

Fuel fill
Tube.

Fuel
Pickup Tube.

Содержание DECATHLON
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды