Seagull Models CLASSIC UGLY STICK Скачать руководство пользователя страница 2

Страница: 2 / 25

CLASSIC UGLY STICK

Instruction Manual.

Thank you for choosing the

CLASSIC UGLY STICK

ARTF by

SEAGULL MODELS

COMPANY LTD

,. The

CLASSIC UGLY STICK

was designed with the intermediate/

advanced sport flyer in mind. It is a sport airplane which is easy to fly and quick to as-

semble. The airframe is conventionally built using balsa, plywood to make it strong-

er than the average ARTF, yet the design allows the aeroplane to be kept light. You will

find that most of the work has been done for you already. The motor mount has been fit-

ted and the hinges are pre-installed. Flying the

CLASSIC UGLY STICK

is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read

this manual throughly before starting assembly of your

CLASSIC UGLY STICK

. Use the

parts listing below to indentify all parts.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs offer a variety

of training procedures designed to help the new pilot on his way to successful R/C flight.

They will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

Содержание CLASSIC UGLY STICK


























Результаты поиска

Содержание CLASSIC UGLY STICK

Отзывы:

Похожие инструкции для CLASSIC UGLY STICK

Бренды по названию

Популярные бренды

Seagull Models CLASSIC UGLY STICK, Инструкция по сборке

Результаты поиска

Содержание CLASSIC UGLY STICK

Отзывы:

Похожие инструкции для CLASSIC UGLY STICK

Бренды по названию

Популярные бренды