Seagate ST9500430SS - Constellation 7200 500 GB Hard Drive Скачать руководство пользователя страница 59

Страница: 59 / 78

Constellation SAS Product Manual, Rev. E

[1]

Constellation drives can format to 512, 520 or 528 bytes per logical block.

[2]

Warning.

Power loss during flash programming can result in firmware corruption. This usually makes the

drive inoperable.

[3]

Reference Mode Sense command 1Ah for mode pages supported.

[4]

Y = Yes. Command is supported.

N = No. Command is not supported.

A = Support is available on special request.

Verify (10)

2Fh

BYTCHK bit

Verify (12)

AFh

Verify (16)

AFh

Verify (32)

7Fh/000Ah

Write (6)

0Ah

Write (10)

2Ah

DPO bit

FUA bit

Write (12)

AAh

Write (16)

8Ah

Write (32)

7Fh/000Bh

Write and Verify (10)

2Eh

DPO bit

Write and Verify (12)

AEh

Write and Verify (16)

8Eh

Write and Verify (32)

7Fh/000Ch

Write Buffer (modes 0, 2, supported)

3Bh

Y (non-SED drives only)

Write Buffer

3Bh

Firmware Download option (modes 5, 7, Ah and Bh) [3]

Y (non-SED drives only)

Firmware Download option (modes 4, 5, 7)

Y (SED drives only)

Write Long (10)

3Fh

Write Long (16)

9Fh/11h

Write Same (10)

41h

PBdata

LBdata

Write Same (16)

93h

Write Same (32)

7Fh/000Dh

XDRead

52h

XDWrite

50h

XPWrite

51h

Table 6:

Supported commands

Command name

Command code

Supported

Содержание ST9500430SS - Constellation 7200 500 GB Hard Drive















































































Результаты поиска

Содержание ST9500430SS - Constellation 7200 500 GB Hard Drive

Отзывы:

Похожие инструкции для ST9500430SS - Constellation 7200 500 GB Hard Drive

Бренды по названию

Популярные бренды

Seagate ST9500430SS - Constellation 7200 500 GB Hard Drive, Руководство по эксплуатации продукта

Результаты поиска

Содержание ST9500430SS - Constellation 7200 500 GB Hard Drive

Отзывы:

Похожие инструкции для ST9500430SS - Constellation 7200 500 GB Hard Drive

Бренды по названию

Популярные бренды