manualshive.com logo in svg

Seagate ST320UM001, Руководство по эксплуатации продукта

Поделиться
Скачать
Seagate ST320UM001 Скачать руководство пользователя страница 17

Seagate Laptop Thin SSHD SATA Product Manual, Rev. E

  16

 Configuring and Mounting the Drive 

3.0

Configuring and Mounting the Drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

Handling and Static-Discharge Precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the 
following standard handling and static-discharge precautions.

3.2

Configuring the Drive

Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host adapter. There is no master/slave 
relationship because each drive is considered a master in a point-to-point relationships. If two drives are attached on one Serial ATA host adapter, 
the host operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are Device 0 
(master) devices.

3.2.1

Serial ATA Cables and Connectors

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 
AWG with a maximum length of one meter (39.37 in). Refer to 

Table 8

 for connector pin definitions. Either end of the SATA signal cable can be 

attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host receptacle incorporate 
features that enable the direct connection to be hot pluggable and blind mateable. For installations which require cables, users can connect the 
drive as shown in

 Figure 2

.

Figure 2

Attaching SATA Cabling

Each cable is keyed to ensure correct orientation. Seagate Laptop Thin SSHD SATA drives support latching SATA connectors. 

CAUTION

• Keep the drive in the electrostatic discharge (ESD) bag until users are ready for installation to limit 

the drive’s exposure to ESD.

• Before handling the drive, put on a grounded wrist strap, or ground oneself frequently by touching 

the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap 
throughout the entire installation procedure.

• Handle the drive by its edges or frame 

only

.

• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

• Always rest the drive on a padded, antistatic surface until users mount it in the computer.

• Do not touch the connector pins or the printed circuit board.

• Do not remove the factory-installed labels from the drive or cover them with additional labels. 

Removal voids the warranty. Some factory-installed labels contain information needed to service 
the drive. Other labels are used to seal out dirt and contamination.

Power cable

Signal cable

Signal connector

Power connector

Содержание ST320UM001




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды