manualshive.com logo in svg

Seagate ST300MM0048, Руководство по эксплуатации продукта


Поделиться
Скачать
background image

Seagate Enterprise Performance 10K HDD v8 Product Manual, Rev. A

  30

  

6.5.4

Shock and vibration

Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is installed in an

 

enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur internally to the enclosure resulting in

 

drive movement in excess of the stated limits. If this situation is apparent, it may be necessary to modify the enclosure to minimize

 

drive movement.

The limits of shock and vibration defined within this document are specified with the drive mounted by any of the four methods 
shown in Figure 5, and in accordance with the restrictions of Section 9.3.

6.5.4.1

Shock

a. Operating

The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding:

•

40 Gs at a maximum duration of 11ms (half sinewave)

•

25 Gs at a maximum duration of 2ms (half sinewave)

Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.

b. Non-operating

The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes both isolated drives 
and integrated drives.

The drive subjected to nonrepetitive shock not exceeding the three values below, shall not exhibit device damage or perfor-
mance degradation.

•

80 Gs at a maximum duration of 11ms (half sinewave)

•

400 Gs at a maximum duration of 2ms (half sinewave)

•

300 Gs at a maximum duration of 0.5ms (half sinewave)

Shock may be applied in the X, Y, or Z axis.

c. Packaged

Seagate finished drive bulk packs are designed and tested to meet or exceed applicable ISTA and ASTM standards. Volume fin-
ished drives will be shipped from Seagate factories on pallets to minimize freight costs and ease material handling. Seagate fin-
ished drive bulk packs may be shipped individually. For less than full shipments, instructions are printed on the bulk pack carton

 

for minimum drive quantities and proper drive placement. 

Figure 5. 

Recommended mounting

Note

Image is for reference only, may not represent actual drive.

Содержание ST300MM0048


























































Отзывы:

Нет отзывов

Похожие инструкции для ST300MM0048

Бренды по названию

Популярные бренды

Загрузить еще бренды