background image

Seagate SkyHawk AI Serial ATA Product Manual, Rev. C

  12

  

2.6

Environmental limits

Temperature and humidity values experienced by the drive must be such that condensation does not occur on any 
drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C).

2.6.1

Temperature

a. Operating

32°F to 149°F (0°C ambient to 65°C drive reported) temperature range with a maximum temperature gradient of 36°F 
(20°C) per hour.

The maximum allowable drive reported temperature is 149°F (65°C).

Air flow may be required to achieve consistent nominal drive temperature values (see 

Section 3.4

). To confirm that the 

required cooling is provided for the electronics and HDA, place the drive in its final mechanical configuration, and 
perform random write/read operations. After the temperatures stabilize, monitor the current drive temperature using 
the SMART temperature attribute 194 or Device Statistics log 04h page 5.

b. Non-operating

–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification 
assumes that the drive is packaged in the shipping container designed by Seagate for use with drive.

 

Figure 2. 

Location of the HDA temperature check point

2.6.2

Humidity

The values below assume that no condensation on the drive occurs. Maximum wet bulb temperature is 84.2°F (29°C).

2.6.2.1

Relative humidity

2.6.2.2

Effective Altitude (sea level)

 

 

Caution

To maintain optimal performance drives should be run at nominal drive temperatures and humidity.

 

Seagate does not recommend operating at sustained extreme temperatures. 
Operating at higher temperatures will reduce useful life of the product

 

 

See 

Section 2.10, "Reliability"

 for rated MTBF device operating condition requirements.

Note

Image is for reference only, may not represent actual drive

Operating:

5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.

Nonoperating:

5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.

Operating:

–304.8 m to 3048 m (–1000 ft. to 10,000+ ft.)

Nonoperating:

–304.8 m to 12,192 m (–1000 ft. to 40,000+ ft.)

HDA

T

emperature

Che

c

k

 

Point

Содержание SKYHAWK SURVEILLANCE AI 5 E Series





























Отзывы: