GSM-R5-Tx_User_Manual_EN_v1-16.docx
Page # 1 of
6
GSM-R5-T, GSM-R5-TI, -TU
1.
Introduction
GSM-R5-Tx is a device designed
for DIN rail mounting
. GSM-R5-Tx can control one
independent electrical circuit in a building, e.g. one circuit of an accumulator stove or
circuit for entry gate or garage gate opening. The control is made via SMS messages or
by ringing. The device is ready to operate immediately after connection to power supply
and inserting of a SIM card of any GSM operator. The GSM-R5-Tx has one relay output,
which can control a coil of a contactor. An electrical appliance e.g. electric heating
system can be connected to this contactor. The GSM-R5-Tx has also one logical input
and one logical output. The logical input can be activated by external voltage 8 to
30V
DC/AC
. The GSM-R5-Tx can react on input status change by ringing or sending and
SMS on preset phone number. It is
also possible to readout the status
of this input via status SMS from
the GSM-R5-Tx. Analog input is
designed for
measuring the temperature or
current 0-20mA or voltage 0-10V.
Analog input can be used for
automatic regulation of output
OUT and can control connected
heating system to maintain the
preset
temperature.
The
temperature of a temperature
sensor can be readout via SMS.
2.
Package
1pc GSM-R5-T or GSM-R5-TI or GSM-R5-TU
1pc
GSM antenna GSM-ANT11K
1pc 8 pin connector (3.5mm), 1pc 2 pin connector (3.5mm)
1pc screwdriver 2mm
1pc mini USB cable
3.
Recommended accessories
GSM-C-T2 temperature sensor with cable 1m
4.
Instalation
1.
To operate the GSM RELAY a SIM card of any GSM
operator is necessary. SIM card must be functional, active and must have PIN code
turned off. Also some credit is necessary if the SIM card is pre-paid.
2.
Insert this prepared SIM card into the GSM-R2-T device (cut corner first, contacts
up
–
towards the inscription SIM). The correct insertion is indicated by mechanical
click noise. Push gently and release to remove the SIM card.
3.
Now it’s pos
sible to connect GSM antenna and power supply 12V or 24V to GSM-
R5-Tx. If the power supply is OK, the green LED (right from PWR connector) will
light on. Cca
1 minute
later the blue LED diode
GSM
will start flashing with a
period of 4 sec.
4.
To make the first test of the GSM-R5-Tx, press the button for local control of
output Y2(OUT). The green LED (near Y2) will light on. Than use your mobile
telephone which you want to use to control the appliance and send a SMS text
message
1234 ON
to the telephone number of the SIM card inserted into the GSM-
R5-Tx. This will switch off the output Y2(OUT) and the green LED will light off.
GSM-R5-Tx automatically sends a confirmation message on performing the
operation. (You can change the password 1234 later in configuration)
5.
Try “
ringing
” on device. You can make pulse on
Y2(OUT) for ca. 4 seconds by
calling on GSM-R5-Tx (with factory settings). The device hangs up the call and
makes pulse on the output. This can be used for example for opening an entrance
gate. You have to use the same phone number as was in the very first SMS sent to
the device.
6.
Try temperature regulation
to 25°C
. Output Y2(OUT) will be switched on and off
depending on the temperature
input A1(°C). Connect
the temperature sensor into
the temperature
input A1(°C) and
send SMS in form of 1234 TEMP25. Regulation
can be canceled by SMS with command 1234 OFF or pressing the button BTN.
7.
GSM-R5-Tx
factory setting is possible to restore by sending SMS message
1234 !FACTORY. If you made a backup configuration of SeaConfigurator settings
(Settings tab -> Files button -> File option), you can restore your settings from this
backup (Settings tab -> Files button -> File option).
8.
The names of the inputs, outputs (their states) and the command names can be
modified according to your ideas using the
SeaConfigurator
configuration
software. This configuration program can be downloaded free of charge from
(enter the word „Configurator“ in the search) and install it on
your PC.
5.
Technical specificatins
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Dimensions
Width
W
54
mm
Height
H
24
mm
Depth
D
(w/o connectors)
86
mm
Supply
Voltage
max. power
supply
(during phone
call, empty
battery and relay
ON)
8 V
DC
12 V
AC
12 V
3.3 W
30 V
V
DC/AC
W
Standby
(connected to
GSM network)
12 V
DC
30 mA
Digital output
“
Y2(OUT)
”
, signal relay
Voltage
U
3
12
60
V
Current
I
2
A
Digital input
“
X3 (IN)
”
Voltage
U
3
4
30
V
Current
I
1,5
mA
Analog input
Temperature
measuring
Al variants
-30
+55
°C
Current
measuring
Only GSM-R5-TI
0
–
20 mA
V
Voltage
measuring
Only GSM-R5-TU
0
–
10 V
mA
Accumulator
Li-ION
3,7
V
Temperature
Storage
tSTG
-40
+85
°C
Operational
tA
-20
+65
°C
Use GSM-R5-Tx inside box with ingress protection at least IP44
!
*) Temperature sensor GSM-C-T2 is not part of the package.
6.
Hardware
6.1
Power supply, Input and Output
Power supply connector has two pins. I/O connector has 8 pins: digital output (relay
contact), digital input (optocoupler), analog input for temperature sensor and +4V
accumulator. Power supply is in a range +8 V
DC
(+12 V
AC
) to 30 V
DC/AC
. It means polarity
of power supply is not important.
Connector
Description
Parameter
Y2(OUT)
Galvanically separated relay contacts
60 V / 2A
X3(IN)
Optocoupler with a resistor 2 kOhm
max 30V
DC
A1 (°C)
A1 (°C/mA)
A1 (°C/V)
version GSM-R5-T
version GSM-R5-TI
version GSM-R5-TU
KTY 81-210
KTY 81-210 or 0-20mA
KTY 81-210 or 0-10V
4V
Internal Li-ION accumulator for input
supply equipped by protective serial
resistor 50 Ohm
4V,
MAX
10 mA
PWR
Power supply
See Technical parameters
6.2
Recommended connection
Before inserting the SIM card into the GSM-R5-Tx device, it is
necessary to turn off setting of the “PIN code”!
Insert the active SIM card (= at least one call was made) to any mobile phone
and turn off the requirement of setting the PIN. On most mobile telephones,
this option can be found in menu “Setting the telephone protection” or “Setup
-> Security -
> PIN control”.
