12. Auxiliary 1 Mode. Selects from momentary, 10 second timed, or latched operation for Auxiliary 1. Momentary op-
eration provides an output for as long as the transmitter button is pressed. Timed operation provides an output that
turns on for 10 seconds each time the transmitter button is pressed. If the button is pressed again during the 30
seconds, the output will turn off. Latched operation provides an output that turns on when the transmitter button is
pressed and remains on until the transmitter button is pressed again.
13. Unlock with Auxiliary 1. When selected, activating the Auxiliary 1 output (usually used to open the trunk) will
disarm the alarm.
14. Starter Confirmation Chirps. When Enabled, horn will chirp to confirm Starter Active state. Enable Auxiliary Start
Activation. Enable to use the axillary start feature if used in keless entry mode.
15. Start in Valet Mode. Selects whether or not the vehicle can remote start while in the valet mode.
16. Lock After Start. When selected, the doors will automatically lock after remote starting.
17. Lock After Shutdown. When selected, the doors will automatically lock after remote shutdown.
18. Engine Run Time. Selects between 15 or 25 minutes for the remote start run cycle.
19. Automatic Start Mode. Selects between every two hours or every hours for the automatic engine starting feature.
20. Tachless Sense Crank Time. Selecting engine crank time automatically selects the tachless mode and one of three
crank times. If the normal engine crank time is too short increase the time by selecting one of the two additional
extended crank time options.
Normal - 0.8Sec.
Extended - 1.0Sec.
Super Extended - 1.4Sec.
Tachless Mode. Determines the engine status using an advanced software routine, without requiring connection to
the vehicle’s tachometer. Tachless operation may not be compatible with some vehicles or in severe temperatures,
in which case the tach wire must be connected.
21. Remote Start Program. This dual program branch sets the engine mode for Gas or Diesel, and learns the vehicle’s
RPM threshold. Learning the RPM threshold automatically selects the RPM monitor mode. For installation into a diesel
equipped vehicle, first set the engine type to diesel before learning RPM. Tach Monitor Mode. Monitors the vehicle’s
tach wire (or a fuel injection wire) in real-time to determine engine status and adjust starter crank time automatically.
If programmed for Tach Monitor, the vehicle’s tach signal will have to be learned before initial operation (see below).
RPM Learn. Start the engine, enter Branch 21 and press Button 1 to learn the vehicle’s tach signal. The horn will
chirp and the LED will flash once to confirm learning of the tach signal and entering Tach Monitor Mode. The horn
will chirp four times and the LED will flash four times if the tach signal was not learned, engine sense mode will not
be changed. Gas Engine. Sets the engine type for Gasoline. Diesel Engine. Sets the engine type for Diesel and mon-
itors the glow plug input to make sure the glow plugs are warm before cranking the starter. If the glow plug wire is
not connected, the built-in timer waits 15 seconds before automatically cranking the starter.
22. Ignition 2 Relay Program. Selects one of three operating modes for the Ignition 2 relay output: Ignition 2, Accessory
2, or Starter 2.
26. Data Bus Input Trigger. When enabled, all available trigger from the Data Bus Module will be monitored.
( door,hood,brake and all other triggers will not be nessecery to hard wire).
27. Horn Chirp Duration. Selects between Normal,(default) Extended, and super extended horn On time During chirping
of the horn.
28. Starter Disable Output Mode. Select between Starter Disable output, Factory Rearm output and Second Auxiliary
output, on the orange wire.
29. Selects between Astra 1000RS and Astra 4000RS - doesn’t apply to Astra 300RS.
30. When enabled doors unlock before start.
31. Data Port Interface Mode: Selects between iDatalink and Fortin module communications.
System Programming
