INTRODUCTION
Thank you for purchasing the Flat Elastic Velvet Curved projection screen. This screen is made entirely in Italy with first-class materials, including a high quality projection
surface to guarantee excellent performance for your installation.
WARNINGS
Before installing the screen, please read the following instructions carefully. We would recommend that these instructions are stored safely for future reference.
When opening the packaging of the screen, please DO NOT USE CUTTERS or OTHER SHARP TOOLS that can damage the screen inside. During opening the packaging and during
installation, it is reccomended to use work gloves.
Depending on the screen weight, it has to be handled by at least two or three persons taking care to the following ratio KG/PERSON: MALE 25 kg. – FEMALE 15 kg.
After assembling the screen, there could result some wrinkles on the projection surface, due to packaging and transport.
These wrinkles will disappear within 48/72 hours,
under the condition that the screen is installed inside a room with at least 20°C temperature. In case the room temperature is higher than 20°C, the wrinkles will disappear
quicker.
In case of persistant wrinkles or if you need to remove the wrinkles in a very short time, we suggest to use an hairdryer.
Warning: use the hairdryer at least 40 cm.
from the projection surface and move it constantly and evenly across the projection cloth.
If this warning is not respected, the surface could be damaged permanently. In
case during assembling of the projection cloth on the frame, the surface results apparently too small, please leave it 24 hrs in a room with 20-24°C temperature. After this,
the cloth will be more elastic and it will be easier to mount it onto the frame.
The manufacturer does not take responsibility for any damage to property or personal injury if the screen is used outside of recommended specifications or in case of
incorrect/poor quality installation.
CERTIFICATIONS
Flat Elastic Velvet Curved are certified.
The surfaces for projection used on the products are cadmium-free and are fire-proof certified as follows:
-
class M1 – WHITE PEARL, CINESOUND, BRIGHT CONTRAST 3D, FRONTREAR, REAR PLUS
-
class M2 – FOLDAWAY, LUMI-GREY, LUMI-GREY MICROPERFORATED
-
class B1 – WHITE, MICROPERFORATED
-
NFPA 701 – REAR LUX
WARRANTY
This projection screen is guaranteed 2 years from the purchase date for manufacturing defects.
Responsibility is limited to repairing or substitution of the defected components and without any other charge at our expense.
Warranty is officially voided if:
1)
the screen has been dismantled or it is returned with collision damage or defective due to incorrect installation;
2)
the screen results damaged due to repairing or modifications made by non-authorized people;
3)
the sticker regarding the serial number of the product has been altered, deleted, removed or is illegible.
DO NOT install this screen nearby or over heating or air conditioning systems, because PVC is a plastic material which dilates and remains damaged if it is subjected to heat
and/or cool air.
DO NOT install this screen either facing direct sun light or blocking a window as PVC could be damaged and make waves for the explanations given above.
The PVC cloth is very sensitive to temperature range.
We advise you to wait 2 hours for the screen to acclimatise before using the screen after delivery, especially if screen is brought into a warm environment from cold.
DO NOT WASH the projection surface with alcohol or solvent nor with commercial cleaners. Every now and then dust the surface with a dry and clean duster.
Please, be very careful because any kind of stain on the PVC cloth is inerasable.
The screen has to be mounted with all the supplied mounting brackets.
DO NOT HANG TO THE SCREEN and DO NOT HANG ANY OBJECT to it. Please take care that children DO NOT PLAY with the screen as they can get severely injured.
The manufacturer will not accept returns of screens for repair without manufacturer’s authorization (RMA number) and without a suitable packaging.
INSTALLATION INSTRUCTIONS
1.
FRAME ASSEMBLY
Lay the frame segments on the floor with the anchoring cursors facing upwards. In order to avoid damages to the velvet finishing of the frame we advise to lay
the frame on a soft and clean cloth.
Connect the base and height segments using the metal edges supplied in order to make a rectangle (Fig. 1).
2.
PROJECTION SURFACE ASSEMBLY
Lay the frame with the anchoring cursors facing upwards. Put the projection surface on the frame with the reflecting side facing downwards and be careful not
to get it dirty.
Insert the galvanized rods into the perimeter pockets; In order to tight the screen surface put the rubber bands into the holes and hook them to the cursors (Fig.
2a – 2b – 2c – 2d), STARTING FROM THE OPPOSITE FOUR ANGLES.
3. The FLAT ELASTIC CURVED screens are provided with sliding mounting brackets which allow an easy wall positioning using the supplied telescopic brackets
(Fig. 3).
4. In order to calculate the distances where to position the telescopic brackets (Fig. 4), please see scheme in Fig. 5.
5. Once you have mounted the screen to its telescopic brackets, please assure the screen with the supplied metallic clips (Fig. 6).
The manufacturer guarantees the squareness of the frame after the installation, only if the frame is hanged to the wall with the anchoring brackets mounted
on the upper and bottom part of the frame.
Squareness of the frame is not guaranteed in case the screen is mounted in different ways (e.g. metal chains from the ceiling) from what above written.
At the end of the installation, please check that the frame is perfectly levelled.
CAUTION: CHECK EVERY 6 MONTHS THAT SCREWS WALL PLUGS AND BRACKETS ARE IN GOOD CONDITIONS AND WELL TIGHTENED.
IT IS FORBIDDEN TO STAY UNDER THE PROJECTION SCREEN.
IT IS FORBIDDEN TO USE THE PROJECTION SCREEN OUTDOOR.
INSTALLATION MANUAL
ENGLISH
FLAT ELASTIC VELVET
CURVED
