Scosche TIQ01 Скачать руководство пользователя страница 8

Страница: 8 / 8

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a WPC device,

pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

CAUTION: Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the product.

NOTE: This equipment has been tested and found to comply with the limits for a wireless

power charger, pursuant to Part 18 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generated, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that interference will occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined

turning the equipment off and on, the user in

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC STATEMENT

This device complies with industry Canada License-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device. This equipment complies with IC RSS-102 radiation exposure

limits set forth for an uncontrolled environment. This transmitter must not be co-located

or operated in conjunction with any other antenna or transmitter.

For complete warranty details or questions

visit us online at www.scosche.com or contact us at:

www.scosche.com/contact

[email protected]

1 (BOO) 363-4490 ext.1

Содержание TIQ01









Результаты поиска

Содержание TIQ01

Отзывы:

Бренды по названию

Популярные бренды

Scosche TIQ01, Быстрый старт

Результаты поиска

Содержание TIQ01

Отзывы:

Бренды по названию

Популярные бренды