background image

Keep the amp away from moisture, and never put any beverages on top of the amplifier,
no matter how convenient it may seem!

Only change fuses with the amp unplugged from the outlet!

There are potentially lethal voltages present inside the amplifier. Do not open the 
amplifier chassis unless authorized and are a qualified technician.

Limited Lifetime Warranty

Science Amplifiers are warranted to be free from defects in workmanship for the lifetime of 

the original owner. Electronic components such as capacitors, resistors, transformers, jacks, 
and potentiometers are warranted for 3 years (not including tubes, see below). Any part 

determined defective by Science Amplification within the 3 year period shall be repaired or 
replaced by Science Amplification without charge for parts and labor provided the unit is 

returned and transportation costs prepaid. Science Amplification will pay return shipping 
costs to the original owner. Any unauthorized repair, modification, or tampering voids this 

warranty.

The warranty excludes:

Normal wear and tear: worn out tubes, jacks, cosmetic damage, etc.

Misuse and abuse: operating the amp without a speaker connected (although the amp 
has some built-in protection against this), operating the amp into the wrong speaker 

load, improper tube installation, using the wrong value fuses, maladjustment of bias 
controls, etc. 

Accidental damage: Dropping the amp, spilling liquid inside, etc.

Acts of "God”: Natural disasters and other non-preventable/foreseeable events that 
damage the amplifier.

Tubes, unless within manufacture's warranty period of 90 days (replacements offered 
at manufacturer's discretion).

Any damage caused by authorized or unauthorized repair or modification that is not 
performed by Science Amplification.

For warranty service, please email 

[email protected]

 for return authorization. Amplifiers

must be sent back in the original packaging or equivalent packaging. The cost of return 

shipping to Science Amplification is to be prepaid by the owner. Science Amplification is not 

10

Содержание Street Sweeper MkII















Отзывы: