background image

If a fuse blows, it's a good thing! Fuses are put in place for safety and to protect the most 

expensive parts of the amplifier. Fuses can blow for various reasons, however the most 
common is a output tube failure. To check if a fuse is blown, push and twist counter-clockwise 

to remove the fuse holder and see if the small wire inside the glass is broken. There may also 
be a burnt area the inside of the glass.

If you replace a fuse, and it blows again, there is likely a  more serious problem. Please contact 

us before changing the fuse again at 

[email protected]

 so we can further assist you with 

the trouble-shooting. 

Safety

Always use a 3-prong cable into a grounded outlet. This makes sure the amplifier is 

always grounded and safe in the rare occurrence the chassis should become "live" 
(electrified).

Tubes become very hot during normal operation. Allow them to cool before handling 
to prevent burns.

Never change tubes with the amplifier ON.

Always make sure the amp's vents are open, allowing heat to escape and air to flow 

freely.

Keep the amp away from moisture, and never put any beverages on top of the amplifier,

no matter how convenient it may seem!

Only change fuses with the amp unplugged from the wall!

There are potentially lethal voltages present inside the amplifier. Do not open the 
amplifier chassis unless authorized and are a qualified technician.

Limited Lifetime Warranty

Science Amplifiers are warranted to be free from defects in workmanship for the lifetime of 

the original owner. Electronic components such as capacitors, resistors, transformers, jacks, 
and potentiometers are warranted for 5 years (not including tubes, see below). Any part 

determined defective by Science Amplification within the 5 year period shall be repaired or 
replaced by Science Amplification without charge for parts and labor provided the unit is 

returned and transportation costs prepaid. Science Amplification will pay return shipping 
costs to the original owner. Any unauthorized repair, modification, or tampering voids this 

10

Содержание DECOLONIZER













Отзывы: