manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

8.13

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Serial Port Communications and Commands

Command Set

>>

MAP 1:D2 <Enter>

Port 1, Data Region METER Map

Data Item   Starting Address   Type  

_YEAR       2800h              int
DAY_OF_YEAR 2801h              int
TIME(ms)    2802h              int[2]
IA(A)       2804h              float[2]
IB(A)       2808h              float[2]
IC(A)       280Ch              float[2]
VA(V)       2810h              float[2]
VB(V)       2814h              float[2]
VC(V)       2818h              float[2]
IAB(A)      281Ch              float[2]
IBC(A)      2820h              float[2]
ICA(A)      2824h              float[2]
VAB(V)      2828h              float[2]
VBC(V)      282Ch              float[2]
VCA(V)      2830h              float[2]
PA(MW)      2834h              float
QA(MVAR)    2836h              float
PB(MW)      2838h              float
QB(MVAR)    283Ah              float
PC(MW)      283Ch              float
QC(MVAR)    283Eh              float
P(MW)       2840h              float
Q(MVAR)     2842h              float
I0(A)       2844h              float[2]
I1(A)       2848h              float[2]
I2(A)       284Ch              float[2]
V0(V)       2850h              float[2]
V1(V)       2854h              float[2]
V2(V)       2858h              float[2]

*>>

Figure 8.20

Data Region MAP Command

Each item within a region has a label, a numeric address (given in 
hexadecimal), and a type. The types are “char” for character data, “int” for 
integer data, and “float” for floating point data. If an item consists of an array 
of these entries, the number of items is indicated in brackets after the type 
specifier, e.g., int[2] means there are two integers stored. For vector quantities, 
the first float contains the magnitude and the second float contains the angle. 
In the example above, IA(A) magnitude is at address 2804h and IA(A) angle 
is at address 2806h.

Add the BL parameter to the 

MAP

 command to receive bit label information 

if it is available. The example in 

Figure 8.21

 illustrates the BL parameter.

*>>

MAP 2:TARGET BL <Enter>

Port 2, Data Region TARGET Map

Data Item   Starting Address  Type   Bit Labels

_YEAR       4800h             int
DAY_OF_YEAR 4801h             int
TIME(ms)    4802h             int[2]
TARGET      4804h             char[9]
            4804h             INST  A     B     C     Q    N    RS    LO  
            4805h             51P   50L   50H   51QP  50Q  51NP 50NL  50NH 
            4806h             51T   50LT  50C   51QT  50QT 51NT 50NLT 27  
            4807h             79RS  79CY  79LO  79SH  52AT 52BT IN6   IN5  
            4808h             PDEM  QDEM  NDEM  TF    CF   TCMA  ST   TRIP 
            4809h             A     B     C     D     E    F     G    H   
            480Ah             J     KT    L     V     W    X     Y    ZT  
            480Bh             *     *     IN6   IN5   IN4  IN3   IN2  IN1  
            480Ch             *     TRIP  CLOSE A1    A2   A3    A4   ALRM 

*>>

Figure 8.21

MAP Command With BL Option

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Xinje XG Series User Manual preview
XG Series
Бренд: Xinje Страницы: 76
Lorex LNR100 SERIES Instruction Manual preview
LNR100 SERIES
Бренд: Lorex Страницы: 186
EVS Neuron NFR2000 Installation And Service Manual preview
Neuron NFR2000
Бренд: EVS Страницы: 30
SIIG IO1037 Quick Installation Manual preview
IO1037
Бренд: SIIG Страницы: 6
Barco Encore VPx Installation Manual preview
Encore VPx
Бренд: Barco Страницы: 30
Avenview DVI-PROWALL-9X Instruction Manual preview
DVI-PROWALL-9X
Бренд: Avenview Страницы: 28
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Бренд: Lattice Semiconductor Страницы: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Бренд: Paradyne Страницы: 19
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Бренд: Ista Страницы: 16
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Бренд: ICP DAS USA Страницы: 31
Miranda Imagestore Intuition+ User Manual preview
Imagestore Intuition+
Бренд: Miranda Страницы: 60
Digisol DG-SR2004 User Manual preview
DG-SR2004
Бренд: Digisol Страницы: 73
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Бренд: PairGain Страницы: 48
Robotis OpenCM 485 Manual preview
OpenCM 485
Бренд: Robotis Страницы: 10
IEI Technology PUZZLE-IN005 User Manual preview
PUZZLE-IN005
Бренд: IEI Technology Страницы: 106
Behringer X-MADI Quick Start Manual preview
X-MADI
Бренд: Behringer Страницы: 15
Proxim 68568r1 Installation And Management Manual preview
68568r1
Бренд: Proxim Страницы: 65
JCAT FEMTO Quick Start Manual preview
FEMTO
Бренд: JCAT Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды