manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.23

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

Automatic Message (SET A) Settings

SET A Settings

When you send the 

SET A

 command to a specific port, the SEL-2032 prompts 

you for responses based on the type of device connected to that port.

Table 7.6

Automatic Message (SET A) Settings Information 

 (Sheet 1 of 3)

Setting

Comment

Description

AUTOBUF

Save unsolicited messages (Y/N).

 

You enter Y (Yes) to save unsolicited messages received by the 
SEL-2032. Ports configured for IEDs can buffer unsolicited messages. 
User-defined commands work regardless of this setting. Not available for 
Master or Printer.

STARTUP

Prompt. Port startup string.

You enter a startup string for the device attached to this port. The startup 
string supports devices that need some initialization on power-up. When 
the SEL-2032 is powered-up, these startup messages are transmitted. 
Typically, this string is used on SEL relays that need to be at Access 
Level 1 or Access Level 2 for automatic data collection by the SEL-2032. 
Not available for Master ports.

The SEL-2032 does not show this setting to a Level 1 user of the 
SEL-2032. This is to prevent an unauthorized user from getting access to 
passwords that may be embedded in the startup string.

The startup string is sent:

When you accept setting changes after the 

SWAP

 or 

COPY

commands.

At power up.

When an inactive port becomes active.

When you accept SET A setting changes.

When leaving transparent communications with a device.

SEND_OPER

Send operate command
on logic bit transition (Y/N/YP). 

Use this setting to enable automated control of the attached SEL device. 
The YP selection indicates that remote bits should always be pulsed (see 

Automated Control on page 7.25

).

REC_SER

Enable Automatic Sequential 
Events Recorder Collection (Y/N). 

Set to Y (Yes) to enable automatic SER data collection from an SEL IED. 
Not all SEL IEDs support this feature.

Note

: If REC_SER = Y, data region 8 (D8) stores the relay SER data. 

You can still send messages using MESG8, but you will not be 
allowed to parse a response.

SP_RATE

Synchrophasor messages per 
minute (N = NONE, 1, 2, 3, 4, 6, 
10, 12, 15, 20, 30, 60)

Set to a numeric value to enable automatic synchrophasor data collection 
from the attached SEL IED. Set to “N” to disable data collection. Not all 
SEL IEDs support this feature at all data rates.

NOCONN

Block external connections to this 
port. 

Set to NA to enable modem, transparent and virtual terminal connections 
to this port. Set to SEL

OGIC

 control equation that equals 1 when you want 

connections to be disabled (see 

Restricting Port Access with NOCONN

).

MSG_CNT

How many auto-message 
sequences (0–12). 

You enter the number of the auto-message(s) you wish to use. Messages 
1–8 have an associated data area to store responses, messages 9–12 are 
for messages only.

PRINT_ALL

Print all unsolicited messages
(Y/N). 

You set to Y (Yes) to print all unsolicited messages received by the 
SEL-2032 to a Printer port. Only those messages received on ports that 
have AUTOBUF = Y are printed. The PRINT_ALL prompt only appears 
on ports with a DEVICE = P for printer. This setting occupies the
Message 1 position. You can create more selective printing functions 
using SEL

OGIC

 control equations and message strings on other message 

functions.

CLEAR_BUF

Clear unsolicited message buffer 
after print (Y/N). 

You set to Y (Yes) to clear the unsolicited message buffer after printing. 
Only applies to Printer ports.

Note:

 Up to 12 auto-messages may be defined using the ISSUE

x

 and 

MESG

x

 settings. The first 8 may have their responses parsed using 

the PARSE

x

 setting.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

2N OfficeRoute Quick Manual preview
OfficeRoute
Бренд: 2N Страницы: 11
2N stargate How To Set preview
stargate
Бренд: 2N Страницы: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Бренд: 2N Telekomunikace Страницы: 24
Yaesu FT-817 - Modification Instructions preview
FT-817 -
Бренд: Yaesu Страницы: 2
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Бренд: mikroElektronika Страницы: 3
Teletronics International TT 900 User Manual preview
TT 900
Бренд: Teletronics International Страницы: 57
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Бренд: Delta Electronics Страницы: 1
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Бренд: EMS Страницы: 52
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Бренд: Supero Страницы: 16
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Бренд: IFM Electronic Страницы: 14
Quadram Quadboard Operation Manual preview
Quadboard
Бренд: Quadram Страницы: 21
Infrant Technologies READYNAS X6 Installation Manual preview
READYNAS X6
Бренд: Infrant Technologies Страницы: 2
Honeywell 7800 SERIES RM7895A Manual preview
7800 SERIES RM7895A
Бренд: Honeywell Страницы: 32
Honeywell GENT VSINTM-PCB-UPG Installation preview
GENT VSINTM-PCB-UPG
Бренд: Honeywell Страницы: 4
Honeywell HX2 Reference Manual preview
HX2
Бренд: Honeywell Страницы: 310
Honeywell Gamewell Velociti AMM-4F Installation And Maintenance Instructions preview
Gamewell Velociti AMM-4F
Бренд: Honeywell Страницы: 2
Compaq ML370 - ProLiant - G3 User Manual preview
ML370 - ProLiant - G3
Бренд: Compaq Страницы: 2
StarTech.com 8STHSB220SAT25B Instruction Manual preview
8STHSB220SAT25B
Бренд: StarTech.com Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды