manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.26

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Settings

Automatic Message (SET A) Settings

Restricting Port 
Access with 
NOCONN

You can use the NOCONN setting to terminate any active Modem, 
Transparent, and Virtual Terminal connections and disable access to a port. 
The SEL

OGIC

 equation you enter for the NOCONN setting controls the value 

of the NOCONN bit for that port. When the NOCONN bit asserts on a port 
with any of the aforementioned connections, transmissions in progress are 
aborted, reception of characters are terminated, and the connections are 
dropped. The termination will appear as a port timeout. 

When a Modem, Transparent, or Virtual Terminal connection exists on a port 
or SEL Master port, the SEL-2032 checks the state of the port’s NOCONN bit 
at least once per second.

When the NOCONN bit asserts, the reception and transmission of data will be 
restricted as defined below.

Modem Ports

The SEL-2032 checks the NOCONN bit before answering a call from a 
modem.  If the bit is asserted (1), then the SEL-2032 will not answer.

When the NOCONN bit is asserted, the SEL-2032 will abort an automatic 
message when the \I…/ string is read.  This includes an automatic dial-out 
message string.  If you prefer to not have automatic dial-out blocked, you can 
adjust the NOCONN logic so the NOCONN bit is always de-asserted (0) 
when dial-out is triggered.

If you connect via modem to a Master port to create a transparent (or Virtual 
Terminal) connection to a Slave port or protocol card, assertion of the 
NOCONN bit on the Master port will terminate both the modem connection 
and the connection to the Slave port or card.

Master SEL Ports

When the NOCONN bit is asserted on a Master SEL port, the SEL-2032 
limits data reception to Fast Operate commands, clears the XOFF status (to 
enable transmission of characters once NOCONN is de-asserted) and restricts 
access to the port.  The SEL-2032 will only process Fast Operate commands 
while the NOCONN bit is asserted.  All other commands, messages and 
characters will be ignored.  If you also require Fast Operate commands to be 
ignored, you must set the FAST_OP setting to ‘N’.  While the NOCONN bit is 
asserted, the SEL-2032 will not output a command prompt in response to any 
commands or messages.

While the NOCONN bit is asserted, the SEL-2032 will continue to transmit 
any message triggered by the ISSUE

x

 setting. The NUM_MESG counter will 

be incremented whenever a message is triggered (Master ports do not support 
parsing or storing responses from a triggered message, so you will not be able 
to detect communication failures or bad messages). You may override the 
transmission of messages while NOCONN is asserted by including 

!(<port 

number>:NOCONN)

 in the ISSUE

x

 setting.

If Unsolicited SER reporting is enabled and the NOCONN bit is asserted, the 
SEL-2032 shall temporarily disable Unsolicited SER reporting.  Once the 
NOCONN bit is de-asserted, Unsolicited SER reporting will resume.  It is not 
necessary for the Fast Message client to re-enable SER reporting if it was 
enabled before NOCONN was de-asserted.  If an Unsolicited SER message is 
unacknowledged when the NOCONN bit asserted, it shall be regenerated with 
the exact same data content except for the status byte (which will contain the 
current system state) once the NOCONN bit is de-asserted. It is recommended 

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Zhone 6211 Quick Installation Instructions preview
6211
Бренд: Zhone Страницы: 1
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Бренд: Jetter Страницы: 67
Sennheiser Surround Dongle User Manual preview
Surround Dongle
Бренд: Sennheiser Страницы: 18
Idis DR-8400 Installation Manual preview
DR-8400
Бренд: Idis Страницы: 31
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Бренд: NXP Semiconductors Страницы: 54
Renesas H8S/2437 Hardware Manual preview
H8S/2437
Бренд: Renesas Страницы: 746
ZyXEL Communications POE-12 Specifications preview
POE-12
Бренд: ZyXEL Communications Страницы: 2
Xcellon DRD-501 User Manual preview
DRD-501
Бренд: Xcellon Страницы: 24
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Бренд: ADTRAN Страницы: 2
LST ZEB2-1 Specifications preview
ZEB2-1
Бренд: LST Страницы: 1
Corsair ELITE LCD UPGRADE KIT Manual preview
ELITE LCD UPGRADE KIT
Бренд: Corsair Страницы: 11
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Бренд: Moxa Technologies Страницы: 2
Alphacool EISBAER PRO Quick Start Manual preview
EISBAER PRO
Бренд: Alphacool Страницы: 9
Supermicro BPN-SAS3-LB16A-N10 User Manual preview
BPN-SAS3-LB16A-N10
Бренд: Supermicro Страницы: 11
SonicWALL Internet Security Appliances Administrator'S Manual preview
Internet Security Appliances
Бренд: SonicWALL Страницы: 293
Lattice Semiconductor mVision AR0234 User Manual preview
mVision AR0234
Бренд: Lattice Semiconductor Страницы: 25
ADLINK Technology ROScube-I Series User Manual preview
ROScube-I Series
Бренд: ADLINK Technology Страницы: 95
ICS Advent COMM4AT/EX Product Manual preview
COMM4AT/EX
Бренд: ICS Advent Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды