manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

4.7

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

SEL

OGIC

 Control Equations

Outputs

Figure 4.5

Unsuccessful Auto-Message Trigger

The database delay region of the 

STATUS

 command response indicates which 

auto-messages are unsuccessful. You may need to increase the ISSUE period 
to eliminate repeated unsuccessful auto-message triggers.

Another interesting case to consider is when SEL

OGIC

 control equations 

contain elements that are cleared by the triggered auto-message. If such an 
element is set again before the auto-message processing is complete, further 
triggering may be disabled. For example, consider the following trigger and 
message settings:

Equation 4.2

Equation 4.3

These settings are meant to output any unsolicited messages received on 
Ports 1 and 2. However, 1:UMB can become set while \DAC2/ is being 
processed, leaving the trigger condition in a set state and precluding any 
further rising edges; the trigger condition has become disabled. 

Figure 4.6

 

illustrates this problem.

Figure 4.6

Trigger Lock-Out Problem

You can prevent this problem by writing a SEL

OGIC

 control equation that 

forces the trigger condition to reset itself immediately.

Auto-Message 

Operation 

Completes

Unsuccessful 

Auto-Message

Trigger

Auto-Message

Is Triggered

ISSUE1

D1

DLY1

ISSUE2

1:UMB+2:UMB

=

MESG2

\DAC1/\DAC2/

=

Auto-Message 

Operation 

Completes

Completion of  

\DAC2/ Processing

Clears 2:UMB

Completion of  

\DAC1/ Processing

Clears 1:UMB

Auto-Message

Is Triggered

1:UMB Set by 

New Unsolicited 

Messages

1:UMB

2:UMB

ISSUE2

D2

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Acconeer A111 User Manual preview
A111
Бренд: Acconeer Страницы: 32
e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Бренд: e-Line Technology Страницы: 34
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Бренд: Lattice Semiconductor Страницы: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Бренд: Lattice Semiconductor Страницы: 13
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
AMD SB710 User Manual preview
SB710
Бренд: AMD Страницы: 20
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Бренд: LSI Страницы: 3
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Бренд: Hauppauge Страницы: 62
Magma ExpressBox7 Quick Installation Manual preview
ExpressBox7
Бренд: Magma Страницы: 2
Cypress Semiconductor CY7C1350G Specification Sheet preview
CY7C1350G
Бренд: Cypress Semiconductor Страницы: 15
SriHome NVS001B Quick Operation Manual preview
NVS001B
Бренд: SriHome Страницы: 12
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Бренд: IEI Technology Страницы: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Бренд: RadioSPECTRAL Страницы: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Бренд: ZALMAN Страницы: 9
JETWAY 939GT2-Ultra Series User Manual preview
939GT2-Ultra Series
Бренд: JETWAY Страницы: 55
A-Trend OPTI495XLC VL-BUS 3/486 Manual preview
OPTI495XLC VL-BUS 3/486
Бренд: A-Trend Страницы: 16
Extron electronics IPL Pro Series User Manual preview
IPL Pro Series
Бренд: Extron electronics Страницы: 10
MikroTik CCR2004-16G-2S+PC Quick Manual preview
CCR2004-16G-2S+PC
Бренд: MikroTik Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды