manualshive.com logo in svg

Schwank STR Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Schwank STR Series Скачать руководство пользователя страница 6

SP-MSTR-AC-11A 

STR Manual 

RD: NOV, 2003 

RL: 11 

KH 

Page 2 

3.  PRE-INSTALLATION SURVEY 

The 

Schwank STR

 heating system must   

have    gas    piping   of   correct diameter, 
length, and arrangement to function properly.  
For  this  reason,  a  layout  drawing  is            
necessary. 

Carefully survey area to be heated. For best 
results, whenever possible, place burner and 
combustion chamber in coldest area. 

4.  MOUNTING CLEARANCES 

Schwank STR 

Series tube heaters must be 

mounted with minimum clearances between 
the reflector surface and combustibles as 
shown in FIGURE 1,  TABLE 2 (page 3). 
 
For recommended heater placement   refer to 
TABLE 3 (page 3). 

Heaters should also be located in relation to 
building  construction  and  equipment,  to     
allowing a minimum clearance of 24 inches 
from  end  of  burner  housing  to  enable          
servicing and cleaning of burner, blower and        
controls.  

2.  INSTALLATION IN GARAGES 

Schwank STR

 Series tube heaters are        

approved for use in garages.  The  installation 
must conform to local building codes or, in 
the absence of    local codes, to the standard 
NFPA No. 54 (ANSI Z223.1 latest edition), 
in the U.S.A. and the CSA B149.1-00, and 
CAN1.2.16-M81 in Canada.   

In a garage installation, the minimum 

 

 

 

 

clearance from the bottom of an infra-red 
heater to the upper surface of a  vehicle shall 
not be less than the  certified clearance to 
combustible material as indicated on the 
heater. 

TS-

TS-

TS-

TS-

4510-

4520-

1420-

1430-

CX

CX

CX

CX

1

 

1

 

1

 

 

1

Stand-Alone Tube Kits require no additional tube kits.
Primary Tube Kits require at least one additional Secondary Tube Kit.
Secondary Tube Kits require a Primary Tube Kit.
Secondary Tube Kit TS-1010-AX can also be used as a 10 ft extension kit.  The installer
may  need to remove the turbulator (refer to Turbulator Chart in the I&O Manual).

STR  60 20

JS-R060-A N/L

STR  60 30

JS-R060-A N/L

STR  45 10

JS-R045-A N/L

STR  45 20

JS-R045-A N/L

STR TUBE KIT PART # & QUANTITY 

REQUIRED

ASSEMBLY CHART

Stand-Alone Kits Only

HEATER MODEL

BURNER KIT 

STR HEATER KIT

Содержание STR Series


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды