Schwank ITT - ITTU Скачать руководство пользователя страница 1

Страница: 1 / 52

GP-MSET-EX-6A

SET(U) / ITT(U) Manual

RD: MAY 2009

RL: 06A - BA

INSTALLATION / OWNER’S MANUAL

Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death.

Read the installation and operating and maintenance instruc-
tions thoroughly before installing or servicing this equipment.

SAFETY ALERT:

This heater must be installed and serviced only by a trained gas service techni-
cian. Failure to comply could result in personal injury, death, fire and/or property
damage.

Do not store or use gasoline or other flammable vapours and liquids in the
vicinity of this or any other gas fired appliance.

IF YOU SMELL GAS:



Extinguish any open flame



Do not attempt to light this or any other appliance



Don’t touch any electrical switch, or telephone



Immediately call your gas supplier from a neighbor’s phone



Follow any and all instruction from your gas supplier



If your gas supplier is not available, call the fire department

WARNING

FIELD CONVERTIBILITY:

This appliance is field con-
vertible to LP gas.

Keep this manual in a secure place .
Record for future reference

Model #:

Serial #:

(located on heater rating label)

Model

SET - SETU

Model

ITT - ITTU

TWO STAGE

LOW INTENSITY TUBE TYPE INFRARED HEATERS

Содержание ITT - ITTU





















































Результаты поиска

Содержание ITT - ITTU

Отзывы:

Похожие инструкции для ITT - ITTU

Бренды по названию

Популярные бренды

Schwank ITT - ITTU, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ITT - ITTU

Отзывы:

Похожие инструкции для ITT - ITTU

Бренды по названию

Популярные бренды