Technical specifications
Battery
Alkali 2 x AA, 1.5 V
Battery life
Up to 4-5 years
Backlight
Green LED
Ambient temperature
0˚ to +40 ˚C
Battery monitoring
The sensor has a built-in monitoring circuit
which detects a low or critical battery level.
Transmission frequency
868.42 MHz
Transmission range in normal buildings
Up to 30 m
Transmission power
Max. 1 mW
IP degree of protection
21
Dimensions
81 mm x 66 mm x 21 mm
Configuration Command Class
Functions
No. Configuration
parameter
Standard
setting
Area
Coding
1
Temperature Report
threshold
0,5 °C
0.1 to 10 °C
2 bytes
1 = 0.1 °C
100 = 10.0 °C
2
Set-point display
resolution
0,5 °C
From 0.1 to 10 ° C in
steps of 0.1 ° C
2 bytes
1 = 0.1 °C
100 = 10.0 °C
3
Min. set-point and
override limit
12 °C
Min. 0 ° C to max.
setpoint/output
2 bytes
0 = 0 °C
40 = 40 °C
4
Max set-point and
override limit
28 °C
Min. setpoint/output
to max. 40 °C
6
Setpoint control
function
Activated
Deactivated/activated 1 byte
0 = deactivated
1 = activated
7
Temporarily override
scheduler
Activated
Deactivated/activated
8
Setpoint in
Thermostat_
Setpoint_Reports
Heating
Heating #1,
cooling #1,
auto changeover
1 byte
1 = heating #1
2 = cooling #1
10 = auto
changeover
9
LED on time
100 ms
100 to 500 ms in
steps of 100 ms
1 byte
1 = 100 ms
5 = 500 ms
5
LED Flash period
1 s
0 to 65,535 seconds
2 bytes
10
Number of LED
flashes (duration)
5
0 to 255 x flashes
1 byte
11
LED Color
Green
Green, red
1 byte
0x01 = green
0x02 = red
1. Raumtemperatursensor
Command Class
SENSOR_
MULTILEVEL
The room temperature is shown on the
display as the icon indicates. If inserted
in the Z-Wave network the temperature
is reported to the controller when the
device is switched on as well as during
changes in temperature, in which the
configured limit is exceeded.
Display accuracy
0,1 °C
Sensor read
Every 5 minutes
Report send
When switching on
If you exceed the
reporting threshold
CONFIGURATION
COMMAND CLASS
Default setting
Area
Report threshold
0,5 °C
0,1 to 10 °C
2. Rocker switch
Command Class
CENTRAL_SCENE
When clicking the LED button a
CENTRAL_SCENE_NOTIFICATION is
sent to the controller.
Supported key
attributes
0x00/0x01/0x02
3. LED control
Command Class
INDICATOR
The controller can trigger and stop a
flashing session on the LED button using
the set display command. The frequency,
flashing frequency and colour of the
session are controlled by 4 configuration
parameters.
Indicator Set
0xFF = start
LED flashing session
0x00 = stop
current session
CONFIGURATION
COMMAND CLASS
Default setting
Area
LED on time
100 ms
100 to 500 ms in steps of 100 ms
LED Flash period
1 s
0 to 65535 seconds
Number of LED flashes
(duration)
5
0 to 255 x flashing
LED colour
Green
Green, red
4. Change setpoint
Command Class
THERMOSTAT_
SETPOINT
The up and down arrow keys are used
to select a new setpoint temperature.
After selection of a setpoint this flashes
for 5 seconds. Thereafter, the measured
temperature is displayed again and the
Z-Wave RS sends the selected tempera-
ture as THERMOSTAT_SETPOINT_
REPORT to the Z-Wave controller.
Indicator Set
0xFF = LED-
flashing session starts
0x00 = stop
current session
CONFIGURATION
COMMAND CLASS
Default setting
Area
Setpoint control
function
Activated
Deactivated/activated
Set-point display
resolution
0,5 °C
From 0.1 to 10 °C in steps of 0.1 °C
Max set-point and
override limit
28 °C
From min. setpoint/clip to max. 40 °C
Min. set-point and
override limit
12 °C
From min. 0 °C to max. setpoint/clip
Setpoint in
Thermostat_
Setpoint_Reports
Heating #1
Heating #1,
cooling #1,
auto changeover
5. Scheduler override thermostat
Command Class
SCHEDULE
The up and down arrow keys are used to
select the temporary override temperature.
The selected value flashes on the display for
5 seconds. Press the LED button before the
5 seconds are over to select the number of
hours for the override. The selected number
of hours flashes for 5 seconds. Thereafter,
the measured temperature is displayed again
and the Z-Wave RS sends the selected tem-
perature and the number of hours as SCHE-
DULE_REPORT to the Z-Wave controller.
CONFIGURATION
COMMAND CLASS
Default setting
Area
Temporarily override
scheduler
Activated
Deactivated/activated
Set-point display
resolution
0,5 °C
From 0.1 to 10 °C in steps of 0.1 °C
Max set-point and
override limit
28 °C
From min. setpoint/clip to max. 40 °C
Min. set-point and
override limit
12 °C
From min. 0 °C to max. setpoint/clip
Z-Wave networks
Z-Wave RS can be installed and operated in any Z-Wave network with other Z-Wave certified devices
from other manufacturers. Independently from respective manufacturers all permanently powered
Z-Wave nodes function as Repeaters within a network
Z-Wave best practice
• After the successful „paste“ the controller must send a WAKE_UP_INTERVAL_SET command to
Z-Wave RS to specify where and when Z-Wave RS should communicate wirelessly.
• After issuing the command WAKE_UP_INTERVAL_SET, the controller must assign return routes, so
that Z-Wave RS can reach its goal, i.e. the node ID given by the command WAKE_UP_INTERVAL_SET
• The node ID given by the command WAKE_UP_INTERVAL_SET applies to a permanently switched-on
device that responds to commands sent from Z-Wave RS. If the controller is turned off for long
periods, the batteries of the Z-Wave RS are used up too quickly.
• Although Z-Wave RS responds to individual commands, multiple commands must always be used to
ensure the two year battery life.
Delete from Z-Wave
• Press „Exclusion/Remove“ on the Z-Wave controller.
• Keep the three buttons on the Z-Wave RS pressed for 5 seconds (up, down and LED buttons).
• Check the process status on the controller and Z-Wave RS.
Z-Wave wake up
A controller can only communicate with Z-Wave RS when the device is switched on. The intervals in
which Z-Wave RS is turned on can be adjusted by means of the command class „switch on.“ The
default setting for switching on is 60 minutes. Z-Wave RS can be turned on manually by pressing one
of three buttons and then stays on for 10 seconds.
Resetting to factory default settings
1. Remove one of the batteries.
2. Hold the LED button for about five seconds when
reinserting the battery until the LED flashes red.
The Z-Wave RS is now reset to the factory default settings.
