SCHUNK MEQ3 200-2 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 49

background image

Troubleshooting

40

01.00|1343374_MES3 / MEQ3 / MEW3 |en

Troubleshooting

The clamping areas do not unlock

Possible cause

Remedial measures

Defective air connections

Check air supply

Pressure below minimum

Check operating pressure (min. 5 bar)

A component is broken (e.g. due to
overloading)

Replace the module or send it to SCHUNK for
repair

Excess tensile load on clamping pins

Reduce support weight

The clamping areas do not unlock perfectly

Possible cause

Remedial measures

Pressure below minimum

Check operating pressure (min. 5 bar)

The modules were not operated with
oiled compressed air

Install maintenance unit with oiler

Hose diameter below minimum

for required hose diameters, see chapter
"Securing and connecting"

The turbo connection is still pressurized,
this is applicable for module height
extensions or the clamping station with
turbo function required for mounting

Ventilate the connection

The quick-change pallet systems no longer open quietly

Possible cause

Remedial measures

The clamping faces on the clamping slides
and on the clamping pin are dirty

Remove the clamping pallet and clean the
clamping faces on the clamping slides and on
the clamping pins. Clean all clamping modules
installed on the clamping slides

8

8.1

8.2

8.3

«
...
38
39
40
41
42
...
»

Содержание MEQ3 200-2


















































Отзывы:

Нет отзывов

Похожие инструкции для MEQ3 200-2

Ecocutter ECC-125

Бренд: Alpha Professional Tools Страницы: 36

Бренд: Milwaukee Страницы: 37

Бренд: Alpha Professional Tools Страницы: 40

Бренд: P.Lindberg Страницы: 86

Бренд: Hitachi Страницы: 158

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 32

Бренд: KitchenAid Страницы: 44

Бренд: Stiga Страницы: 318

Бренд: Panther Страницы: 45

Бренд: SIRI Страницы: 36

Бренд: Mac Afric Страницы: 6

Бренд: Maruyama Страницы: 16

Бренд: Maruyama Страницы: 36

Бренд: EMAK Страницы: 56

Бренд: Stihl Страницы: 344

Бренд: Nakanishi Страницы: 2

Бренд: RAIMONDI Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды