background image

• 4 •

4.  For a positive-ground vehicle, connect the Instant Power’s NEGATIVE (BLACK) clamp to the 

NEGATIVE (NEG, N, -) battery post. Next, connect the POSITIVE (RED) clamp to the vehicle chassis 

or engine block away from the battery.

5.  Turn the switch to the ON position
6.  Crank the engine for no more than 8 seconds. If the engine does not start, wait 2 minutes before 

cranking again.

7.  After the engine starts, turn the switch to the OFF position and remove the unit from the battery.
8.  Charge the unit.

5.2 

USING THE USB PORT 

The USB port provides up to 2A at 5V DC.
1.  Ensure the battery clamps are securely clipped on the storage holders.
2.  Turn the unit ON.
3.  Plug your device into the USB port.
4.  When finished using the USB port, turn the switch to the OFF position.
5.  Charge the unit.

5.3 

USING THE WORK LIGHT

The work light is controlled by a sliding ON/OFF switch located on the front of the unit. 
•  Make sure the lamp is turned OFF when the unit is being recharged or stored. 
•  Position the unit on a flat, stable surface near the intended work area.
•  Ensure the battery clamps are securely clipped on the storage holders.

5.4 

POWERING A 12V DC DEVICE

The unit is a power source for all 12V DC accessories that are equipped with a 12V accessory plug. Use 

it for power outages and on fishing or camping trips.

NOTE: Do not power a 12V device with the unit while charging the internal battery. 
1.  Make sure the device to be powered is OFF before inserting the 12V DC accessory plug into the 12V 

DC accessory outlet.

2.  Open the protective cover of the DC power outlet on the unit. 
3.  Plug the 12V DC device into the DC power outlet and turn on the 12V DC device (if required).
4.  When finished, turn off the DC device (if required) and unplug from the DC power outlet.

CAUTION: Do not use the unit to run appliances that draw more than 20A DC.

NOTE: Extended operation of a 12V DC device may result in excessive battery drain. Recharge the unit 

immediately after unplugging the 12V DC device.
Estimated run-times 

APPLIANCE TYPE

EST WATTAGE

APPROX. USAGE

Cell phone, fluorescent light

4 watts

34 hrs

Radio, fan, depth finder

9 watts

14 hrs

Camcorder

15 watts

7 hrs

Electrical tool

24 watts

5 hrs

Electric cooler

48 watts

2 hours

Car vacuum, air compressor

80 watts

1.8 hrs

NOTE: Actual time may vary. Times are based on the internal battery being fully charged.

Содержание BE01254








Отзывы: