SCHOLTES LPE P832 Скачать руководство пользователя страница 29

Страница: 29 / 48

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However,

we recommend that you add salt,

especially if you live in an area where the water is hard or
very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT

and

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off

the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:

• When the LOW RINSE AID indicator light

on the control panel

is illuminated, a reserve supply of rinse aid is still available

for 1-2 cycles;

1. Open the dispenser

“D”

by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Rinse-aid quantity setting

If you are not completely satisfied with the drying results, you

can adjust the quantity of rinse aid. Switch the dishwasher on

and off using the

ON/OFF

button. Press the

Start/Pause

button

3 times. Start it using the

ON/OFF

button; the setting is shown

on the display

(set to factory level)

Adjust the level of rinse aid supply using the

button

Press the ON/OFF button to save the setting.

If the rinse aid level is set to ZERO, no rinse aid will be supplied.
The LOW RINSE AID indicator light will not be lit if you run out

of rinse aid.
Up to maximum 4 levels can be set based on the dishwasher
model.

• If there are streaks on the crockery, set a low number (1-2.)
• If there are drops of water or limescale marks, set a high

number (3-4.)

Setting water hardness

Every dishwasher is equipped with a water softener which uses

refined salt designed specially for this type of appliance to supply
water without limescale - used to wash the crockery.
This dishwasher has a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.

Switch the dishwasher on and off using the

ON/OFF

button. Press

and hold down the

Start/Pause

button for a few seconds until

you hear a beep. Switch the dishwasher on using the

ON/OFF

button; the set level will appear on the display

(water softener

set to medium level).

Adjust the hardness level using the

button

(1-2-3-4-5

see the

water hardness table)

up to max. 5 levels.

Press the ON/OFF button to save the setting.

Even if using multi-functional tablets, fill the salt dispenser.

(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.

Refined salt removes limescale from the water, thus avoiding

the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• When the green float

cannot be seen by simply looking at

the cap of the salt dispenser;

• When the LOW RINSE AID indicator light on the control panel

is illuminated

;

1. Remove the lower rack and unscrew the

cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.
3. Position the funnel

(see figure)

and

fill the salt dispenser up to the edge

(approximately 1 kg). It is normal for a little

water to leak out.

4. Remove the funnel* and wipe any salt residues away from

the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float

It is advisable to perform this procedure every time you add
salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).

When necessary, measure out the salt before a wash cycle

so that any saline solution which has leaked out of the salt
dispenser is removed.

Only available in selected models.

Water Hardness Table

Average salt dispenser

capacity duration

level

°dH

°fH

mmol/l

months

0 - 6