To Stop a Fare
Press
Fare (red)
switch to stop fare. The
TIME OFF
(red)
indicator
will turn on. The fare will no longer increase with time. Pressing
FARE
(red)
again will resume the fare.
Press
Mem.Tot (green)
switch once to total fare. This adds the value
of the extras to the value of the fare. The total value is shown in
FARE
(green)
display. Pressing
Mem.Tot (green)
again will un-total
the fare.
Press
Ext.Clr (yellow)
switch to clear the display. For meters set to
Auto- Clear, the fare will be cleared when the vehicle is driven a few
metres. If the fare is flashing, press the
Tariff (blue)
switch to clear it.
For multiple hire tariffs, when the fare is totalled, then un-totalled, the
displayed fare is saved to memory.
Sleep Mode & Idle Mode
The G4 meter can be ‘put to sleep’ in which it draws minimal power.
Press
Tariff (blue)
switch while car is stopped to cycle through
available tariffs until sleep-mode is reached. It is only necessary to
put the meter into Sleep Mode if the cab is not used for a few hours.
To turn the meter on, press any switch on the front panel or drive the
car a few metres. The red
RATE
display shows the operating tariff (if
applicable), the switches illuminate and the yellow legends are backlit.
Roof Light
Press
Ext.Clr (yellow)
switch while meter is in Idle-Mode to turn the
roof light ON and OFF.
The yellow
VACNT
indicator lights when the roof light is on.
When a fare is started the roof light turns off automatically. It will turn
on automatically when the fare is cleared.
Display Time and Date
Press
Mem.Tot (green)
switch while meter is in Idle-Mode to display
the current-time. The
EXTRA (orange)
display will show “ct”.
Press
Mem.Tot (green)
switch again to show the current-date
(dd/mm/yy). The
EXTRA (orange)
display will show “cd”.
Setting the Time and Date
– Regular
Press
Mem.Tot (green)
switch while meter is in Idle-Mode followed
quickly by
Ext.Clr (yellow)
switch.
The current time will appear with the hour display flashing.
Press
Fare (red)
switch to step through hours, minutes, year,
month,day.
Press
Tariff (blue)
and
Mem.Tot (green)
switches to adjust each
item up/down respectively.
Press
Ext.Clr (yellow)
switch to return the meter to Idle Mode.
Setting the Time and Date
– Locked Time (inc. Vic Metro)
Press
Mem.Tot (green)
switch while meter is in Idle-Mode. The
EXTRA (orange)
display will show “ct”.
Press
Ext.Clr (yellow)
switch briefly. The
EXTRA (orange)
display
will show “SEt”.
To advance the clock:
o
When the seconds count reaches more than 30, press
Tariff
(blue)
switch. The seconds will advance to 59.
o
Repeat to continue advancing the clock by 30 seconds.
To retard the clock:
o
When the seconds count is between 0 and 29, press and hold
Tariff (blue)
switch. The seconds will go to 0.
o
Keep holding the switch to keep the seconds at 0.
The clock can only be adjusted by up to 90 seconds in a 24 hour
period.
Press
Ext.Clr (yellow)
switch to return the meter to Idle Mode.
Memory Functions
Press
Mem.Tot (green)
switch while meter is in Idle-Mode. The
EXTRA (orange)
display will show “ct”.
Press
Mem.Tot (green)
switch again to step through memory items.
Press
Ext.Clr (yellow)
to return to Idle mode.
ID
Memory Function
ID
Memory Function
ct
Current Time (24 hr)
12
Total Units ($.c)
cd
Current Date (dd/mm/yy)
13
Total Extras ($.c)
01
Shift Money ($.c)
14
Total Trips
02
Shift Money per Hour ($/hr)
15
Paid Kilometres (km)
03
Shift Money per Km ($/km)
16
Total Kilometres (km)
04
Shift Kilometres (km)
17
Current Calibration (Pulses/km)
05
Last Job Fare ($.c)
18
Speedometer Pulse Counter
06
Last Job Extras ($.c)
19
Software Version / Clear Shift
07
Last Job Distance (km)
20
Km Travelled Since Last Job (km)
08
Last Job Start Time(hr/min)
21
Total Distance Units
09
Last Job End Time (hr/min)
22
Total Waiting Time Units
10
Total Money ($.c)
23
Speed (kph) [Tariff ID in W.A]
11
Total Flagfalls ($.c)
24
Tariff ID [Not used in W.A]
Clearing Memory
Shift figure totals may be cleared (Memory items 1, 2, 3 & 4)
To clear, go to memory item 19.
Press and hold
Ext.Clr (yellow)
switch until the word “clear” appears
then disappears from the display.
